What is the warranty for Peak-System products?

Here is the complete hardware warranty section from the supplier. PCAN Adapter: PCAN-USB Adapter & PCAN-USB Adapter (Isolated)

I have a PCAN Adapter and have severed my cable to the service port on the engine. I am trying to confirm the wiring to the data link (from the CAN bus side).

These images show the pinout of the CAN bus side: Image 1 Image 2

Do you have a comparable product to Vector’s CANape and canoe/canalyzer?

You may want to look at the PCAN-USB Adapter with PCAN-Explorer 6 from PEAK. It will not be an exact 1:1 replacement, however.

Will the PCAN Adapter (2021, 2022, 4022, etc.) work with my [XYZ] device?

The PEAK PCAN-USB Adapter is a generic CAN interface for PC which allows CAN data exchange according to ISO 11898-2 with CAN bitrates of up to 1 Mbit/s. You will need to check if your devices also use a High-speed CAN connection per ISO 11898-2 standard. If they do, the chances are good that the PCAN-Adapter will work for you. We offer a 30-day money-back guarantee in the event it does not meet your needs.

What chips/circuitry are inside the PCAN USB Adapter?

The PCAN-USB Adapter has an FPGA with all the CAN controller circuitry, power supply circuits, and a CAN transceiver. For additional details, see the features section.

How does it handle 3.3 volt?

The PCAN-USB Adapter (IPEH-002021/22) will work with any CAN device that is ISO 11898-2 compliant. The adapter uses an NXP PCA82C251 CAN transceiver. Here is a link to the transceiver datasheet for full details on CAN voltages: PCA82C251 Datasheet

I ordered 3 PCAN USB adapters. If I want to connect two of them to talk to each other, and they are the only nodes on the CAN bus, what do I need to accomplish this?

You will need a terminated CAN cable such as our PCAN-Cable 2. Or something similar if you already have existing CAN cables. The DB-9 connector on the PCAN-USB Adapter is male. The cable has female connectors and the needed 120 Ohm termination resistors installed at both ends.

What chips/circuitry are inside the PCAN USB Adapter?

The PCAN-USB Adapter has an NXP CAN controller SJA1000 with 16 MHz clock frequency and an NXP CAN transceiver PCA82C251.

I am searching for a professional CAN Bus analyzer. We need the capability to monitor CAN Bus traffic and identify when message faults occur.

The PCAN-USB Adapter with PCAN-Explorer 6 software will serve your needs best!

I purchased the PCAN-USB Adapter (isolated). What else is required to record and then playback J1939 data?

The PCAN-Explorer V6 software with the J1939 add-in will work. We offer a 30-day trial with full functionality. Email us for your trial today.

I see the PCAN USB interface connects to a USB port, and the description says the interface is Linux compatible via SocketCAN. Does the driver present the socketCAN interface 'itself' (the USB interface being transparent), or will I have to provide the transport between the USB interface and the socketCAN interface?

The PEAK-System Linux page answers many of these questions and more. (SocketCAN is relevant for the SYSTEC USB-CANmodul from a different manufacturer.

I think the PCAN-USB Adapter (isolated) will work for the J1939 task I have. What do I need to be able to record and then playback that data?

The PCAN-Explorer V6 software with the J1939 add-in will work. PCAN-Explorer 6 Software

I purchased the PCAN-USB Adapter. Where can I download the driver for this USB adapter?

Windows and Linux drivers can be downloaded from the “Downloads” tab on the product page beneath the product description.

I have a IPEH-002262-KSM01. Do you have any example projects/files for this device? More than the examples provided in the manual?

The manufacturer has packaged all available files and demo projects into this download .

Is your CANopen Source Code UL (Underwriter Laboratories) certified?

No, our products are European, and CE certification is used for hardware, not software.

Can I download the software?

No, the process of getting the software ready and delivered via FTP transfer from SYSTEC usually takes one to two business days.

How do I set a custom CAN baud rate, for example, 333 kHz?

It is not possible to configure a CAN baud rate of exactly 333 kbit/s on the CAN-Ethernet Gateway V2. However, a baud rate of 333,333 kbit/s can be configured and has been tested. Please refer to the user's manual (section 6.4) for instructions on setting the gateway to this CAN baud rate.

Does the CANmodul1 require that a 120-ohm resistor be connected at the input port/CAN side?

Yes, a 120-ohm termination resistor is required at both ends of a CAN bus. If the CANmodul1 happens to be at the end, then an external bus termination is needed.

Will the CAN controller automatically determine whether it's a Standard or Extended ID?

Correct, no special settings are needed. The CAN controller automatically detects if it's 2.0A (11-bit identifier) or 2.0B (29-bit identifier) CAN specification.

What is the return policy?

Most unopened items in new condition and returned within 90 days will receive a refund or exchange. Some items have a modified return policy noted on the receipt or packing slip. Items that are opened or damaged or do not have a receipt may be denied a refund or exchange. Items purchased online or in-store may be returned to any store. Online purchases may be returned via a major parcel carrier. Click here to initiate a return.

How long does it take to process a refund?

We will reimburse you for returned items in the same way you paid for them. For example, any amounts deducted from a gift card will be credited back to a gift card. For returns by mail, once we receive your return, we will process it within 4–5 business days. It may take up to 7 days after we process the return to reflect in your account, depending on your financial institution's processing time.

What is the policy for late/non-delivery of items ordered online?

Our local teams work diligently to make sure that your order arrives on time, within our normaldelivery hours of 9AM to 8PM in the recipient's time zone. During busy holiday periods like Christmas, Valentine's and Mother's Day, we may extend our delivery hours before 9AM and after 8PM to ensure that all gifts are delivered on time. If for any reason your gift does not arrive on time, our dedicated Customer Service agents will do everything they can to help successfully resolve your issue. Click here to complete the form with your order-related question(s).

When will my credit card be charged?

We'll attempt to securely charge your credit card at the point of purchase online. If there's a problem, you'll be notified on the spot and prompted to use another card. Once we receive verification of sufficient funds, your payment will be completed and transferred securely to us. Your account will be charged in 24 to 48 hours.

Will I be charged sales tax for online orders?

Local and State sales tax will be collected if your recipient's mailing address is in: Arizona California Colorado

What software options do I need to purchase for the GEMAC CAN-Bus Tester 2?

There are 5 different add-on software licenses available. You will need one of the add-on licenses if you use a higher layer protocol such as CANopen, J1939, DeviceNet. There are also options for using a Protocol Monitor for one of these protocols. If you just use plain CAN, you may consider the Protocol Monitor CAN-License key for Protocol Monitor CAN (transmit / receive). The available licenses are as follows: CAN-Bus Tester 2: CANopen bus add-on $1039 CAN-Bus Tester 2: DeviceNet bus add-on $1239 CAN-Bus Tester 2: J1939 bus add-on $659 CAN-Bus Tester 2: Protocol Monitor CAN (Rx/Tx) $649 CAN-Bus Tester 2: Protocol Monitor CANopen (Receive) $519 CAN-Bus Tester 2: Protocol Monitor J1939 (Receive) $519

I'm looking at a GEMAC CAN-bus tester 2 for testing of CAN networks in our machines. Will I be able to debug the hardware side with the package by itself? What does the protocol monitor add-on do?

The protocol monitor does the following: CAN: Reception of CAN message frames incl. filtering, Transmission of CAN message frames and sequences (message lists) What level of testing do you plan to do? We're looking at debugging hardware issues with the network, would like to be able to determine problem messages/nodes on the network. I would recommend getting the protocol monitor license along with the CAN bus tester 2 device. Or you can buy the unit by itself first (available from stock) and see if you are okay without that license. You can always buy it at a later point.

What tools are available for developing a Windows-based CANopen application to talk to various CAN devices?

Phytools offers a number of different solutions for CANopen development on a Windows-based system. If you are looking for a full-featured CANopen source code package, we suggest the SYSTEC CANopen Source Code SO-877. This software is a full buyout license, meaning there will be no additional runtime fees or royalties for deployed products with this code inside. It can be used in combination with any SYSTEC CAN interface module. For developing PC-based applications in Windows, we recommend the CANopen Magic Pro DLL developed by our partner Embedded Systems Academy. This software works in combination with any PC-CAN interface made by PEAK-System Technik, such as their popular PCAN-USB Adapters. Embedded Systems Academy also has other CANopen network configuration tools that may be of interest. You can find more information on the Embedded Systems Academy page.

Are there any limitations to the CANopen Magic evaluation copy?

Yes, there are limitations to the CANopen Magic evaluation copy: 1. Communication with a real CAN bus is not possible. Instead, simulated CANopen nodes may be accessed over a purely internal CAN bus. 2. There is no command line interface to access the CAN bus. Please note: The features in this version match the full version of CANopen Magic Ultimate. There are other versions of CANopen Magic available with smaller feature sets. We hope you enjoy using this software and experimenting with CANopen!

Can I try this software before I purchase?

Yes, please email us for a 30-day PCAN Explorer Trial. You must also have a CAN interface, such as the PCAN USB Adapter. Each trial license includes all available add-in options.

I need a software program for collecting data off the J1939 Vehicle Network and parsing out each PGN and identifying which SPNs are available on the network and are changing in values to show it is valid data. What add-in or other product do I need to perform this?

You can do this with PCAN Explorer 6 with the J1939 add-in. We offer a 30-day trial of PCAN Explorer, and the trial comes with all the add-ins. Email us for your trial copy.

What is a .dbc file? (relevant for PCAN Explorer 6 - CANdb add-in)

A DBC file is a Communication Database for CAN. It is the distributed system's backbone. DBC files are basic text files that include information for decoding raw CAN bus data to physical values or in human-readable form. They specify which signals (e.g., RPM, Vehicle Speed, etc.) are contained within specific messages (i.e., CAN IDs). In developing a distributed ECU network based on CAN, a key component is the communication description in the form of DBC files. Described in DBC databases are the properties of the CAN network, the ECUs connected to the bus, and the CAN messages and signals.

My version of PCAN Trace (1.8.0.50) software is giving a bad file error message when trying to read my customers' 2.1 recordings. Can you help?

The PCAN-Trace can only handle trace files which comply with file version 1.x. A trace file that complies with version 2.x must be converted into file version 1.x with the 'PEAK-Converter.'

I am running PCAN Trace and collecting data off the J1939 Vehicle Network. I want to have a program that parses out each PGN and identifies which SPNs are available on the network and are changing in values to show it is valid data. What add-in or other product do I need to perform this?

PCAN Trace cannot do this, but you can do this with PCAN Explorer 6 with the J1939 add-in. We offer a 30-day trial of PCAN Explorer, and the trial comes with all the add-ins.

I am new to EtherCAT. I am looking for an EtherCAT Slave Unit that runs Linux on Raspberry Pi.

Yes, you can accomplish this with the Gateway Module Ethernet Slave coupled with the appropriate base RevPi module (IPC based on Raspberry Pi).

I need to convert two Modbus TCP devices to one Allen Bradley CompactLogix Ethernet IP. Questions I have are:

1. Hardware required. Looks like (1) KU-PR100066 and (1) KU-PR100088 would work? 2. Any additional hardware part number required to do this? 3. Can I convert both signals with one set of converters? A: The two gateway modules you inquired about (KU-PR100066 and KU-PR100088) will work to create a gateway system that connects Modbus TCP with Ethernet IP. The required connection clip is included. No additional items are needed.

Does the RevPi Core or Core 3 come with a power supply cable?

No, there is no cabling included with the RevPi Core or Core 3.

What are the mounting options for the RevPi Core or Core 3?

The RevPi Core or Core 3 can be mounted on a DIN rail housing (for DIN rail version EN 50022).

Does the RevPi Core or Core 3 come with an SD card?

No, there is no SD card included with the RevPi Core or Core 3. You can use a USB memory stick for data storage.

What are the graphics specs of the RevPi Core or Core 3? I need to drive a large LCD display.

The RevPi Core is based on the Broadcom BCM2711, quad-core Arm Cortex-A72. For more information, visit click here The RevPi Core 3 is based on the Broadcom BCM2837 processor. For more information, click here For more information on the VideoCore subsystem, see click here .

What are the limitations of the CANopen Magic evaluation?

The CANopen Magic evaluation has limitations. Please refer to the documentation and licensing information provided by Embedded Systems Academy, Inc.

What is the HS code for the following items: PCAN Cable 1 w/o termination, PCAN T-Adapter, PCAN-USB Adapter

The HTS code for cables and T-adapters is 8544429000. The PCAN-USB adapter is 8517620050. The ECCN number for all products is EAR99. All are manufactured in Germany.

How do I calculate the baud rate?

There is a tool made by PEAK for calculating the baud rate register settings: baudtool.zip

Are the SYS TEC Canmodul1 and the Kvaser Leaf Light v2 the same product essentially?

The two devices provide similar functionality in that they both connect a PC or laptop via its USB interface to a CAN bus. Both devices support the maximum CAN bitrate of 1 Mbit/s. However, both devices have unique designs in terms of internal circuitry and software API/drivers. There are other differences in terms of CAN message throughput, buffer size, etc. If you are using third-party software that specifically requires the use of the Kvaser Leaf Light V2, then I strongly advise against using a different type of USB-CAN interface.

I'm currently using the PCAN-USB to view 500k CAN bus data on cars. I would like to be able to view the LIN bus data on Chrysler vehicles 2011 and newer. Do I need a dedicated LIN interface or is there one that will do both LIN and CAN?

Phytools offers a PLIN-USB Adapter (dedicated LIN interface) and several interfaces that support both CAN and LIN, including the PCAN USB Pro FD, the Kvaser Hybrid, and the CAN FD LIN Gateway.

I am looking for an isolated CAN repeater, and I saw the one you have rated to 500V. Do you have any rated for higher voltages, around 1.5-2 kV?

The PCAN-Repeater DR establishes a galvanic isolation of up to 5 kV according to IEC60601-1 within a High-speed CAN bus. Both CAN ports are decoupled from each other and from the power supply. All message traffic, including error frames, is forwarded 1:1 between both ports. The PCAN-Repeater DR behaves passively and is transparent from the perspective of the CAN bus. LEDs display the current bus status.

I'm currently using the PCAN-USB Adapter to view 500k CAN bus data on cars. I would like to be able to view the LIN bus data on Chrysler vehicles 2011 and newer. Do I need a dedicated LIN interface or is there one that will do both LIN and CAN?

Phytools offers a PLIN-USB Adapter (dedicated LIN interface) and several interfaces that support both CAN and LIN, including the PCAN USB Pro FD, the Kvaser Hybrid, and the CAN FD LIN Gateway.

I am looking for the ability to connect two CAN FD channels and have the ability to process, manipulate, and filter CAN messages bidirectionally between each bus. Which products do I need?

There are two solutions: PC-based solution or a standalone solution. For the former, you can use PCAN-USB Pro FD Adapter, which has two independent CAN FD capable channels. Any message processing, manipulating, filtering, etc. will require using the corresponding PC software based on the PCAN Basic API. For the latter, use the PCAN Router FD with specially programmed firmware as a stand-alone CAN FD router.

I just need a simple CAN interface with some software that can receive and display CAN messages from other nodes as well as send CAN messages out to other nodes. What device would you recommend?

We suggest a PCAN-USB Interface with the included free PCAN-View software. If you need a device that is able to detect and analyze more of the physical layer properties of a CAN system, we do offer CAN diagnostic tools as well.

MANUFACTURERS

Sort by

Show
24
36
48

View as

Sale

$479

100/1000BASE-T1 Media Converter (Rosenberger H-MTD)
MACH SYSTEMS

Fast/Gigabit Automotive Ethernet to Standard Ethernet Converter The 100/1000BASE-T1 Media Converter realizes a full-duplex physical-layer conversi...
View full details

$479

Sale
Sale

$434

PCAN-MiniDiag FD
PEAK-System Technik

Compact Diagnostic Device for CAN and CAN FD Buses The PCAN-MiniDiag FD is a handheld device for diagnosing and monitoring Classic CAN and CAN FD b...
View full details

$434

Sale
Sale

$361

sysWORXX CANopen I/O-X4
SYS TEC electronic GmbH

A CANopen IO module featuring industrial proven IO's. The module includes a CPU-core including the pre-programmed firmware for CANopen communicatio...
View full details

$361

Sale
Sale

$369

SAE J2716 (SENT) – USB Interface
MACH SYSTEMS

Easily connects a SENT bus to any computer with an USB port The SENT-USB is a two-channel SAE J2716 (Single Edge Nibble Transmission – SENT) to USB...
View full details

$369

Sale
Sale

$729

sysWORXX CANopen IO-C12
SYS TEC electronic GmbH

An Extension module with a mix of Industrial Proven Input & Output signal types. This device provides a mix of industrial proven input and outp...
View full details

$729

Sale
Sale

$57

LIN Connection Cable for PCAN-USB Pro FD
PEAK-System Technik

Pre-configured Cable Set for the PCAN-USB Pro FD Adapter PEAK's PCAN-USB Pro FD and PCAN-USB Pro Adapters route the signals for the two field buses...
View full details

$57

Sale
Sold out

$154

PCAN-MicroMod
PEAK-System Technik

This product is EOL. Product is no longer available. Please consider this newer version instead. Contact Sales@phytools.com for further assistance ...
View full details

$154

Sold out
Sold out

$315

Kvaser Leaf Light V2 HS J1939-13
Kvaser AB

EOL PRODUCT: (ZERO STOCK ON HAND) Replacement for this product: Kvaser Leaf v3 J1939-13 Type II - SKU# KV-01426-8 Kvaser's Leaf Light V2 J1939-13...
View full details

$315

Sold out
Sale

from $1,790

PCAN-Router Pro FD
PEAK-System Technik

Links the data traffic of modern CAN FD and classic CAN buses. With six channels, the PCAN-Router Pro FD Pluggable CAN transceiver modules allow fl...
View full details

from $1,790

Sale
Sale

$369

SAE J2716 (SENT) to RS232 Gateway
MACH SYSTEMS

The interface’s flexibility allows the user to use it in multiple ways. The SAE J2716 (SENT) to RS232 gateway features two bi-directional SENT (Sin...
View full details

$369

Sale
Sale

$139

RevPi Con CAN
KUNBUS

Expansion module allows you to integrate CAN bus capabilities into your RevPi Connect. The expansion module has 4-pin connector to the CAN bus con...
View full details

$139

Sale
Sale

$317

PCAN-MicroMod Analog 1
PEAK-System Technik

The motherboards provide an application-oriented environment. Please note: The product is only available in smaller quantities. Unfortunately, larg...
View full details

$317

Sale
Sale

$317

PCAN-MicroMod Digital 2
PEAK-System Technik

Implementation-ready CAN or CANopen I/O systems suitable for a wide range of industrial control applications. Please note: The product is only avai...
View full details

$317

Sale
Sale

$44

MATEnet Connecting Cables
MACH SYSTEMS

TE MATEnet to MATEnet 2-meter cable harness Accessory for 100/1000BASE-T1 Media Converter (TE MATEnet). Female to female connector ends. n/d

$44

Sale
Sold out

$859

Kvaser Leaf Pro HS V2
Kvaser AB

This product is EOL. (Zero sock on hand) Please consider the Kvaser U100P as the recommended replacement. Kvaser's latest addition to the p...
View full details

$859

Sold out
Sale

from $325

PCAN-PCI insert-card iso (1ch/2ch)
PEAK-System Technik

A cost-effective solution for the connection of a CAN bus to a PC via a 9-pin SUB-D plug. The pin assignment of which corresponds to the CiA recom...
View full details

from $325

Sale
Sale

$109

Kvaser OBD II Extension Cable 5 Meter
Kvaser AB

Kvaser's OBD-II Extension Cable is a highly durable extension cable of 5 metres. Access hard-to-reach OBD2 ports with ease using a 5-meter OBD2 ext...
View full details

$109

Sale
Sale

$0

PCAN-RP1210 API
PEAK-System Technik

An implementation of RP1210 version C with support for CAN and SAE J1939 networks. The Recommended Practice 1210 was defined by the Technology and ...
View full details

$0

Sale
Sale

$196

Gateway Module - Ethernet/IP Slave
KUNBUS

Expansion module for Ethernet/IP Networks. When using our RevPi Ethernet/IP gateway module, integrating Revolution Pi into a Ethernet/IP network is...
View full details

$196

Sale
Sale

from $464

RevPi Connect SE
KUNBUS

A solution for seamless connectivity. The KUNBUS RevPi Connect SE is an intermediate step between the RevPi Connect+ series and the RevPi Connect ...
View full details

from $464

Sale
Sale

$479

100/1000 BASE-T1 to Ethernet Converter (TE MATEnet)
MACH SYSTEMS

Fast/Gigabit Automotive Ethernet to Standard Ethernet converter The 100/1000BASE-T1 Media Converter MATEnet establishes a point-to-point link betwe...
View full details

$479

Sale
Sale

$0

PCAN-Basic
PEAK-System Technik

Allows easy development of powerful software with CAN and CAN FD support. It includes all of the functions that an application needs in order to c...
View full details

$0

Sale
Sale

$749

Kvaser PCIEcan 4xHS
Kvaser AB

Please see the manufacturer's recommended replacement, the PCIEcan 4xCAN v2 (KV-01414-5). Kvaser PCIEcan 4xHS is a highly integrated, high speed ...
View full details

$749

Sale
Sale

from $349

KVASER LEAF V3
Kvaser AB

Quick and easy plug-and-play installation The Kvaser Leaf v3 represents one of the easiest and lowest-cost methods of connecting a computer to a CA...
View full details

from $349

Sale
Sale

$382

sysWORXX CANopen I/O-X6
SYS TEC electronic GmbH

A compact and cost-effective module featuring 8 analog output channels. The module includes a CPU-core with the pre-programmed firmware for CANopen...
View full details

$382

Sale
Sale

$1,039

CAN-Bus Tester 2: CANopen bus add-on
GEMAC

License key to activate higher-layer protocol support CANopen.This software component can only be used in combination with the GEMAC CAN-Bus Tester...
View full details

$1,039

Sale
Sale

$625

Kvaser USBcan II HS/SWC
Kvaser AB

EOL PRODUCT: (Limited to sock on hand) Kvaser's USBcan II HS/SWC is a dual-channel CANbus interface adapter featuring a standard USB 1.1 connection...
View full details

$625

Sale
Sale

$365

PCAN-Router DR
PEAK-System Technik

Features two high-speed CAN channels. The bit rate for each channel is adjusted with a rotary switch located on the front panel of the unit. The m...
View full details

$365

Sale
Sale

$397

PCAN-MicroMod FD Digital 2
PEAK-System Technik

Purchased together with ready-to-use motherboards that provide peripherals for specific requirements. For the connection of CAN, I/O, and power su...
View full details

$397

Sale
Sale

$661

Kvaser Ethercan Light HS
Kvaser AB

CAN to Ethernet interface for remote network access. The Kvaser Ethercan Light HS is a CAN to Ethernet interface that, when linked over the Inter...
View full details

$661

Sale
Sale

$295

PCAN-MicroMod Mix 1 & 2
PEAK-System Technik

Application-specific PCAN-MicroMod Motherboards The motherboards for the PCAN-MicroMod provide an application-oriented environment. Typical charact...
View full details

$295

Sale
Sale

$39

TE MATEnet to Rosenberger H-MTD Adapter
MACH SYSTEMS

TE MATEnet male to Rosenberger H-MTD male (Z-coding) PCB adapter

$39

Sale
Sale

from $303

RevPi Core SE
KUNBUS

A Robust Open Source IPC Based on Raspberry Pi The new RevPi S and SE series are based on the brand-new Raspberry Pi Compute Module 4S. The serie...
View full details

from $303

Sale
Sale

$515

Kvaser Leaf Light R v2
Kvaser AB

A one channel USB interface for CAN with Galvanic Isolation. The Kvaser Leaf Light R v2 is the rugged version of Kvaser’s popular Leaf Light v2 ...
View full details

$515

Sale
Sale

from $355

PCAN-PCI/104 Express card, iso (1ch/2ch)
PEAK-System Technik

End of Life - The Product will be Discontinued Please note: The product is only available in limited quantities and is expected to be discontinued...
View full details

from $355

Sale
Sale

$329

100Base-T1 USB Interface
MACH SYSTEMS

Converter acts as an Ethernet network interface card when plugged into an USB port. The 100BASE-T1 USB Interface (Media Converter) connects a 100BA...
View full details

$329

Sale
Sale

$1,159

Kvaser Hybrid Pro 2xCAN/LIN
Kvaser AB

A must-have "universal interface" for automotive communications. Kvaser Hybrid Pro 2xCAN/LIN is a flexible, dual channel interface that allows each...
View full details

$1,159

Sale
Sale

$649

CAN-Bus Tester 2: Protocol Monitor CAN (Rx/Tx)
GEMAC

Configure connected devices with just one touch of a button. License key to activate protocol monitor CAN (transmit/receive). This software compone...
View full details

$649

Sale
Sale

$949

Kvaser BlackBird V2
Kvaser AB

More powerful and versatile a WLAN solution than Kvaser's original BlackBird. Kvaser BlackBird V2 incorporates a new radio chip that gives it up to...
View full details

$949

Sale
Sale

$403

PCAN-Router w/ Phoenix connector
PEAK-System Technik

A dual-channel CAN module with an NXP LPC21 series programmable microcontroller. This CAN router provides the option of using the CAN messages on ...
View full details

$403

Sale
Sale

$362

PCAN-MicroMod Mix 3
PEAK-System Technik

The motherboard provides an application-oriented environment. Typical characteristics of this product group include a wide supply voltage range an...
View full details

$362

Sale
Sold out

$73

Kvaser OBDII Dsub9 adapter cable 2.5 meter
Kvaser AB

(This product is EOL. Please see the newer version: KV-01407-7) A Kvaser OBD II Adapter Cable connects any Kvaser CAN bus interface with a DSUB9 s...
View full details

$73

Sold out
Sale

$397

PCAN-MicroMod FD Digital 1
PEAK-System Technik

Purchased together with ready-to-use motherboards that provide peripherals for specific requirements. The PCAN-MicroMod FD plug-in board for the co...
View full details

$397

Sale
Sold out

$1,395

SYS TEC USB-CANmodul8
SYS TEC electronic GmbH

This version bundles 8 CAN-channels into one device. As a member of the successful USB CAN Gateway family from SYS TEC, the USB-CANmodul8 version b...
View full details

$1,395

Sold out
Sale

$649

CANtouch: License for "Node Measurement" - CAN
GEMAC

License key to activate the "Node Measurement" feature for CAN bus systems with the GEMAC CANtouch mobile diagnostic device. Correct assignment of ...
View full details

$649

Sale
Sale

$519

CAN-Bus Tester 2: Protocol Monitor CANopen
GEMAC

License key to activate higher-layer protocol support CANopen. This software component can only be used in combination with the GEMAC CAN-Bus Teste...
View full details

$519

Sale
Sale

$14

RevPi PCB Female Connector
KUNBUS

RevPi PCB Female Connector is a spare part. Two units are included with the following RevPi expansion modules: digital I/O module RevPi DIO (KU-PR...
View full details

$14

Sale
Sale

$18

PCAN miniPCIe/M.2 CAN FD 5-pin to DB-9 cable
PEAK-System Technik

NOTE: Cables only. The image shown is for description purposes. PCAN miniPCIe/M.2 CAN FD connection cable to DB-9. Connects miniature connector on...
View full details

$18

Sale