What is the warranty for Peak-System products?

Here is the complete hardware warranty section from the supplier. PCAN Adapter: PCAN-USB Adapter & PCAN-USB Adapter (Isolated)

I have a PCAN Adapter and have severed my cable to the service port on the engine. I am trying to confirm the wiring to the data link (from the CAN bus side).

These images show the pinout of the CAN bus side: Image 1 Image 2

Do you have a comparable product to Vector’s CANape and canoe/canalyzer?

You may want to look at the PCAN-USB Adapter with PCAN-Explorer 6 from PEAK. It will not be an exact 1:1 replacement, however.

Will the PCAN Adapter (2021, 2022, 4022, etc.) work with my [XYZ] device?

The PEAK PCAN-USB Adapter is a generic CAN interface for PC which allows CAN data exchange according to ISO 11898-2 with CAN bitrates of up to 1 Mbit/s. You will need to check if your devices also use a High-speed CAN connection per ISO 11898-2 standard. If they do, the chances are good that the PCAN-Adapter will work for you. We offer a 30-day money-back guarantee in the event it does not meet your needs.

What chips/circuitry are inside the PCAN USB Adapter?

The PCAN-USB Adapter has an FPGA with all the CAN controller circuitry, power supply circuits, and a CAN transceiver. For additional details, see the features section.

How does it handle 3.3 volt?

The PCAN-USB Adapter (IPEH-002021/22) will work with any CAN device that is ISO 11898-2 compliant. The adapter uses an NXP PCA82C251 CAN transceiver. Here is a link to the transceiver datasheet for full details on CAN voltages: PCA82C251 Datasheet

I ordered 3 PCAN USB adapters. If I want to connect two of them to talk to each other, and they are the only nodes on the CAN bus, what do I need to accomplish this?

You will need a terminated CAN cable such as our PCAN-Cable 2. Or something similar if you already have existing CAN cables. The DB-9 connector on the PCAN-USB Adapter is male. The cable has female connectors and the needed 120 Ohm termination resistors installed at both ends.

What chips/circuitry are inside the PCAN USB Adapter?

The PCAN-USB Adapter has an NXP CAN controller SJA1000 with 16 MHz clock frequency and an NXP CAN transceiver PCA82C251.

I am searching for a professional CAN Bus analyzer. We need the capability to monitor CAN Bus traffic and identify when message faults occur.

The PCAN-USB Adapter with PCAN-Explorer 6 software will serve your needs best!

I purchased the PCAN-USB Adapter (isolated). What else is required to record and then playback J1939 data?

The PCAN-Explorer V6 software with the J1939 add-in will work. We offer a 30-day trial with full functionality. Email us for your trial today.

I see the PCAN USB interface connects to a USB port, and the description says the interface is Linux compatible via SocketCAN. Does the driver present the socketCAN interface 'itself' (the USB interface being transparent), or will I have to provide the transport between the USB interface and the socketCAN interface?

The PEAK-System Linux page answers many of these questions and more. (SocketCAN is relevant for the SYSTEC USB-CANmodul from a different manufacturer.

I think the PCAN-USB Adapter (isolated) will work for the J1939 task I have. What do I need to be able to record and then playback that data?

The PCAN-Explorer V6 software with the J1939 add-in will work. PCAN-Explorer 6 Software

I purchased the PCAN-USB Adapter. Where can I download the driver for this USB adapter?

Windows and Linux drivers can be downloaded from the “Downloads” tab on the product page beneath the product description.

I have a IPEH-002262-KSM01. Do you have any example projects/files for this device? More than the examples provided in the manual?

The manufacturer has packaged all available files and demo projects into this download .

Is your CANopen Source Code UL (Underwriter Laboratories) certified?

No, our products are European, and CE certification is used for hardware, not software.

Can I download the software?

No, the process of getting the software ready and delivered via FTP transfer from SYSTEC usually takes one to two business days.

How do I set a custom CAN baud rate, for example, 333 kHz?

It is not possible to configure a CAN baud rate of exactly 333 kbit/s on the CAN-Ethernet Gateway V2. However, a baud rate of 333,333 kbit/s can be configured and has been tested. Please refer to the user's manual (section 6.4) for instructions on setting the gateway to this CAN baud rate.

Does the CANmodul1 require that a 120-ohm resistor be connected at the input port/CAN side?

Yes, a 120-ohm termination resistor is required at both ends of a CAN bus. If the CANmodul1 happens to be at the end, then an external bus termination is needed.

Will the CAN controller automatically determine whether it's a Standard or Extended ID?

Correct, no special settings are needed. The CAN controller automatically detects if it's 2.0A (11-bit identifier) or 2.0B (29-bit identifier) CAN specification.

What is the return policy?

Most unopened items in new condition and returned within 90 days will receive a refund or exchange. Some items have a modified return policy noted on the receipt or packing slip. Items that are opened or damaged or do not have a receipt may be denied a refund or exchange. Items purchased online or in-store may be returned to any store. Online purchases may be returned via a major parcel carrier. Click here to initiate a return.

How long does it take to process a refund?

We will reimburse you for returned items in the same way you paid for them. For example, any amounts deducted from a gift card will be credited back to a gift card. For returns by mail, once we receive your return, we will process it within 4–5 business days. It may take up to 7 days after we process the return to reflect in your account, depending on your financial institution's processing time.

What is the policy for late/non-delivery of items ordered online?

Our local teams work diligently to make sure that your order arrives on time, within our normaldelivery hours of 9AM to 8PM in the recipient's time zone. During busy holiday periods like Christmas, Valentine's and Mother's Day, we may extend our delivery hours before 9AM and after 8PM to ensure that all gifts are delivered on time. If for any reason your gift does not arrive on time, our dedicated Customer Service agents will do everything they can to help successfully resolve your issue. Click here to complete the form with your order-related question(s).

When will my credit card be charged?

We'll attempt to securely charge your credit card at the point of purchase online. If there's a problem, you'll be notified on the spot and prompted to use another card. Once we receive verification of sufficient funds, your payment will be completed and transferred securely to us. Your account will be charged in 24 to 48 hours.

Will I be charged sales tax for online orders?

Local and State sales tax will be collected if your recipient's mailing address is in: Arizona California Colorado

What software options do I need to purchase for the GEMAC CAN-Bus Tester 2?

There are 5 different add-on software licenses available. You will need one of the add-on licenses if you use a higher layer protocol such as CANopen, J1939, DeviceNet. There are also options for using a Protocol Monitor for one of these protocols. If you just use plain CAN, you may consider the Protocol Monitor CAN-License key for Protocol Monitor CAN (transmit / receive). The available licenses are as follows: CAN-Bus Tester 2: CANopen bus add-on $1039 CAN-Bus Tester 2: DeviceNet bus add-on $1239 CAN-Bus Tester 2: J1939 bus add-on $659 CAN-Bus Tester 2: Protocol Monitor CAN (Rx/Tx) $649 CAN-Bus Tester 2: Protocol Monitor CANopen (Receive) $519 CAN-Bus Tester 2: Protocol Monitor J1939 (Receive) $519

I'm looking at a GEMAC CAN-bus tester 2 for testing of CAN networks in our machines. Will I be able to debug the hardware side with the package by itself? What does the protocol monitor add-on do?

The protocol monitor does the following: CAN: Reception of CAN message frames incl. filtering, Transmission of CAN message frames and sequences (message lists) What level of testing do you plan to do? We're looking at debugging hardware issues with the network, would like to be able to determine problem messages/nodes on the network. I would recommend getting the protocol monitor license along with the CAN bus tester 2 device. Or you can buy the unit by itself first (available from stock) and see if you are okay without that license. You can always buy it at a later point.

What tools are available for developing a Windows-based CANopen application to talk to various CAN devices?

Phytools offers a number of different solutions for CANopen development on a Windows-based system. If you are looking for a full-featured CANopen source code package, we suggest the SYSTEC CANopen Source Code SO-877. This software is a full buyout license, meaning there will be no additional runtime fees or royalties for deployed products with this code inside. It can be used in combination with any SYSTEC CAN interface module. For developing PC-based applications in Windows, we recommend the CANopen Magic Pro DLL developed by our partner Embedded Systems Academy. This software works in combination with any PC-CAN interface made by PEAK-System Technik, such as their popular PCAN-USB Adapters. Embedded Systems Academy also has other CANopen network configuration tools that may be of interest. You can find more information on the Embedded Systems Academy page.

Are there any limitations to the CANopen Magic evaluation copy?

Yes, there are limitations to the CANopen Magic evaluation copy: 1. Communication with a real CAN bus is not possible. Instead, simulated CANopen nodes may be accessed over a purely internal CAN bus. 2. There is no command line interface to access the CAN bus. Please note: The features in this version match the full version of CANopen Magic Ultimate. There are other versions of CANopen Magic available with smaller feature sets. We hope you enjoy using this software and experimenting with CANopen!

Can I try this software before I purchase?

Yes, please email us for a 30-day PCAN Explorer Trial. You must also have a CAN interface, such as the PCAN USB Adapter. Each trial license includes all available add-in options.

I need a software program for collecting data off the J1939 Vehicle Network and parsing out each PGN and identifying which SPNs are available on the network and are changing in values to show it is valid data. What add-in or other product do I need to perform this?

You can do this with PCAN Explorer 6 with the J1939 add-in. We offer a 30-day trial of PCAN Explorer, and the trial comes with all the add-ins. Email us for your trial copy.

What is a .dbc file? (relevant for PCAN Explorer 6 - CANdb add-in)

A DBC file is a Communication Database for CAN. It is the distributed system's backbone. DBC files are basic text files that include information for decoding raw CAN bus data to physical values or in human-readable form. They specify which signals (e.g., RPM, Vehicle Speed, etc.) are contained within specific messages (i.e., CAN IDs). In developing a distributed ECU network based on CAN, a key component is the communication description in the form of DBC files. Described in DBC databases are the properties of the CAN network, the ECUs connected to the bus, and the CAN messages and signals.

My version of PCAN Trace (1.8.0.50) software is giving a bad file error message when trying to read my customers' 2.1 recordings. Can you help?

The PCAN-Trace can only handle trace files which comply with file version 1.x. A trace file that complies with version 2.x must be converted into file version 1.x with the 'PEAK-Converter.'

I am running PCAN Trace and collecting data off the J1939 Vehicle Network. I want to have a program that parses out each PGN and identifies which SPNs are available on the network and are changing in values to show it is valid data. What add-in or other product do I need to perform this?

PCAN Trace cannot do this, but you can do this with PCAN Explorer 6 with the J1939 add-in. We offer a 30-day trial of PCAN Explorer, and the trial comes with all the add-ins.

I am new to EtherCAT. I am looking for an EtherCAT Slave Unit that runs Linux on Raspberry Pi.

Yes, you can accomplish this with the Gateway Module Ethernet Slave coupled with the appropriate base RevPi module (IPC based on Raspberry Pi).

I need to convert two Modbus TCP devices to one Allen Bradley CompactLogix Ethernet IP. Questions I have are:

1. Hardware required. Looks like (1) KU-PR100066 and (1) KU-PR100088 would work? 2. Any additional hardware part number required to do this? 3. Can I convert both signals with one set of converters? A: The two gateway modules you inquired about (KU-PR100066 and KU-PR100088) will work to create a gateway system that connects Modbus TCP with Ethernet IP. The required connection clip is included. No additional items are needed.

Does the RevPi Core or Core 3 come with a power supply cable?

No, there is no cabling included with the RevPi Core or Core 3.

What are the mounting options for the RevPi Core or Core 3?

The RevPi Core or Core 3 can be mounted on a DIN rail housing (for DIN rail version EN 50022).

Does the RevPi Core or Core 3 come with an SD card?

No, there is no SD card included with the RevPi Core or Core 3. You can use a USB memory stick for data storage.

What are the graphics specs of the RevPi Core or Core 3? I need to drive a large LCD display.

The RevPi Core is based on the Broadcom BCM2711, quad-core Arm Cortex-A72. For more information, visit click here The RevPi Core 3 is based on the Broadcom BCM2837 processor. For more information, click here For more information on the VideoCore subsystem, see click here .

What are the limitations of the CANopen Magic evaluation?

The CANopen Magic evaluation has limitations. Please refer to the documentation and licensing information provided by Embedded Systems Academy, Inc.

What is the HS code for the following items: PCAN Cable 1 w/o termination, PCAN T-Adapter, PCAN-USB Adapter

The HTS code for cables and T-adapters is 8544429000. The PCAN-USB adapter is 8517620050. The ECCN number for all products is EAR99. All are manufactured in Germany.

How do I calculate the baud rate?

There is a tool made by PEAK for calculating the baud rate register settings: baudtool.zip

Are the SYS TEC Canmodul1 and the Kvaser Leaf Light v2 the same product essentially?

The two devices provide similar functionality in that they both connect a PC or laptop via its USB interface to a CAN bus. Both devices support the maximum CAN bitrate of 1 Mbit/s. However, both devices have unique designs in terms of internal circuitry and software API/drivers. There are other differences in terms of CAN message throughput, buffer size, etc. If you are using third-party software that specifically requires the use of the Kvaser Leaf Light V2, then I strongly advise against using a different type of USB-CAN interface.

I'm currently using the PCAN-USB to view 500k CAN bus data on cars. I would like to be able to view the LIN bus data on Chrysler vehicles 2011 and newer. Do I need a dedicated LIN interface or is there one that will do both LIN and CAN?

Phytools offers a PLIN-USB Adapter (dedicated LIN interface) and several interfaces that support both CAN and LIN, including the PCAN USB Pro FD, the Kvaser Hybrid, and the CAN FD LIN Gateway.

I am looking for an isolated CAN repeater, and I saw the one you have rated to 500V. Do you have any rated for higher voltages, around 1.5-2 kV?

The PCAN-Repeater DR establishes a galvanic isolation of up to 5 kV according to IEC60601-1 within a High-speed CAN bus. Both CAN ports are decoupled from each other and from the power supply. All message traffic, including error frames, is forwarded 1:1 between both ports. The PCAN-Repeater DR behaves passively and is transparent from the perspective of the CAN bus. LEDs display the current bus status.

I'm currently using the PCAN-USB Adapter to view 500k CAN bus data on cars. I would like to be able to view the LIN bus data on Chrysler vehicles 2011 and newer. Do I need a dedicated LIN interface or is there one that will do both LIN and CAN?

Phytools offers a PLIN-USB Adapter (dedicated LIN interface) and several interfaces that support both CAN and LIN, including the PCAN USB Pro FD, the Kvaser Hybrid, and the CAN FD LIN Gateway.

I am looking for the ability to connect two CAN FD channels and have the ability to process, manipulate, and filter CAN messages bidirectionally between each bus. Which products do I need?

There are two solutions: PC-based solution or a standalone solution. For the former, you can use PCAN-USB Pro FD Adapter, which has two independent CAN FD capable channels. Any message processing, manipulating, filtering, etc. will require using the corresponding PC software based on the PCAN Basic API. For the latter, use the PCAN Router FD with specially programmed firmware as a stand-alone CAN FD router.

I just need a simple CAN interface with some software that can receive and display CAN messages from other nodes as well as send CAN messages out to other nodes. What device would you recommend?

We suggest a PCAN-USB Interface with the included free PCAN-View software. If you need a device that is able to detect and analyze more of the physical layer properties of a CAN system, we do offer CAN diagnostic tools as well.

Manufacturers

Sort by

Show
24
36
48

View as

Sale

$519

CAN-Bus Tester 2: Protocol Monitor CANopen
GEMAC

License key to activate higher-layer protocol support CANopen.This software component can only be used in combination with the GEMAC CAN-Bus Tester...
View full details

$519

Sale
Sale

$14

RevPi PCB Female Connector
KUNBUS

This item is a spare part. Two units are included with the following RevPi expansion modules: digital I/O module RevPi DIO (KU-PR100197) digital i...
View full details

$14

Sale
Sale

$18

PCAN miniPCIe/M.2 CAN FD 5-pin to DB-9 cable
PEAK-System Technik

NOTE: This item includes the cables only. The card shown is for description purposes. PCAN miniPCIe/M.2 CAN FD connection cable to DB-9Connects min...
View full details

$18

Sale
Sale

$217

Kvaser OBD II Extension Cable 10 Meter
Kvaser AB

A Kvaser OBD II Extension Cable is an extension cable with a male to female OBD II connector. The cable is made of durable thermoplastic rubber. Al...
View full details

$217

Sale
Sale

$479

PCAN-MicroMOD Evaluation Kit 2
PEAK-System Technik

Please note: The product is only available in smaller quantities. Unfortunately, larger quantities can no longer be produced. Please see the PCAN M...
View full details

$479

Sale
Sale

$1,169

CANopen Magic Professional
Embedded Systems Academy

Professional CANopen configuration and analysis tool. High accuracy timestamps, Electronic Datasheet support, network configuration and easy PDO co...
View full details

$1,169

Sale
Sale

from $399

CAN-LIN Gateway ECU
MACH SYSTEMS

Compact ECU with Dual CAN/CAN FD, LIN, and Multi-Purpose I/O The control unit is fully configurable and can be used as a stand-alone data converter...
View full details

from $399

Sale
Sale

$309

sysWORXX CANopen I/O-X3
SYS TEC electronic GmbH

The CANopen IO-X3 is a very compact and cost effective CANopen IO module featuring a high-density of industrial proven IO's. The module includes a ...
View full details

$309

Sale
Sold out

$465

Kvaser PCIEcan HS V2
Kvaser AB

This product is EOL and not intended for new designs. The replacement product is the Kvaser PCIEcan 1xCAN v3. The Kvaser PCIEcan HS V2 is a highly ...
View full details

$465

Sold out
Sale

$949

Kvaser USBcan Professional HS/HS DSUB
Kvaser AB

This product is EOL and not intended for new designs.Please email us for availability. The replacement model is the Kvaser USBcan Pro 2xHS v2.The K...
View full details

$949

Sale
Sale

from $50

Kvaser Adapter Cable, 30 cm
Kvaser AB

With a standard 9-pin Dsub at one end and a 16-pin OBDII connector at the other, this 30 cm cable connects the Kvaser Leaf v3 or any CAN interface ...
View full details

from $50

Sale
Sale

$315

RevPi Flat
KUNBUS

A Slim Compact Controller Based on Raspberry Pi RevPi Flat is an open source industrial PC for the DIN rail. Equipped with the Raspberry Pi Comput...
View full details

$315

Sale
Sale

$1,795

SYS TEC USB-CANmodul16
SYS TEC electronic GmbH

Based on the successful SYS TEC USB-CANmodul designs, the USB-CANmodul16 bundles 16 high-speed CAN channels in one device, connected to the PC via ...
View full details

$1,795

Sale
Sale

$439

SYS TEC CAN-Ethernet Gateway V2 (Dual CAN Interfaces)
SYS TEC electronic GmbH

The CAN-Ethernet Gateway enables the integration of CAN buses to existing Ethernet topology. Hence, it is suitable as universal PC CAN interface an...
View full details

$439

Sale
Sale

$659

CANtouch: License for "Bus Wiring"
GEMAC

License key to activate the "Bus Wiring" feature of the GEMAC CANtouch mobile diagnostic device. ...
View full details

$659

Sale
Sale

$109

Kvaser OBD II Extension Cable 2.5 Meter
Kvaser AB

A Kvaser OBD II Extension Cable is an extension cable with a male to female OBD II connector. The cable is made of durable thermoplastic rubber. Al...
View full details

$109

Sale
Sale

$119

LabView Driver for PCAN-Developer
KDI Digital Instrumentation

LabVIEW® API for PCAN© Developer 4.x driver This API uses the PCAN©-Developer 4.x API from PEAK-System to establish one or more CAN networks. Usin...
View full details

$119

Sale
Sale

$1,929

PCAN-Developer 4
PEAK-System Technik

Professional CAN and CAN FD Development Package for Windows® PEAK's new PCAN-Developer 4 Software Package is a flexible system for planning, devel...
View full details

$1,929

Sale
Sale

$289

PCAN-MicroMod Digital 1
PEAK-System Technik

Please note: The product is only available in smaller quantities. Unfortunately, larger quantities can no longer be produced. Please see the PCAN M...
View full details

$289

Sale
Sale

$99

LabVIEW API for PLIN
KDI Digital Instrumentation

Leveraging the PLIN© API from PEAK-System, the LabVIEW® API for PLIN allows you to exchange CAN messages via CAN 1.0 / 2.0B and CAN FD with the PLI...
View full details

$99

Sale
Sale

$149

Development Board for CANopen I/O
SYS TEC electronic GmbH

The CANopen Chip Carrier Board provides a flexible development platform for easy start-up and subsequent programming. The flexible design allows ea...
View full details

$149

Sale
Sale

$1,039

CANtouch: License for "Node Measurement" - CANopen
GEMAC

License key to activate the App "Node Measurement" - CANopen.This software component can only be used in combination with the GEMAC CANtouch. Corre...
View full details

$1,039

Sale
Sale

$659

CAN-Bus Tester 2: SAE J1939 bus add-on
GEMAC

License key to activate higher-layer protocol support CANopen.This software component can only be used in combination with the GEMAC CAN-Bus Tester...
View full details

$659

Sale
Sale

$1,239

CAN-Bus Tester 2: DeviceNet bus add-on
GEMAC

License key to activate higher-layer protocol support CANopen.This software component can only be used in combination with the GEMAC CAN-Bus Tester...
View full details

$1,239

Sale
Sale

$459

PCAN-WLAN Gateway DR
PEAK-System Technik

The PCAN-Wireless Gateway DR allows the connection of different CAN busses over IP networks. CAN frames are wrapped in TCP or UDP message packets a...
View full details

$459

Sale
Sale

from $225

PCAN-PC/104 Adapter, iso (1ch/2ch)
PEAK-System Technik

This product is no longer available. The PCAN-PC/104 is a compact PC/104-CAN slot which allows the networking of two CAN buses to a PC/104 system. ...
View full details

from $225

Sale
Sale

$1,979

CANopen Magic Ultimate
Embedded Systems Academy

Professional CANopen configuration, simulation and analysis tool. High accuracy timestamps, Electronic Datasheet support, network configuration and...
View full details

$1,979

Sale
Sale

$589

CANopen Magic Standard
Embedded Systems Academy

Low cost basic CANopen configuration and analysis tool. Runs on all versions of Windows and provides access to Object Dictionary entries, shows mes...
View full details

$589

Sale
Sale

$35

PCAN-Cable M12
PEAK-System Technik

CAN Adapter Cable from D-Sub Socket to M12 Circular Connector M12 circular connectors are robust and offer increased protection against environment...
View full details

$35

Sale
Sale

$985

Kvaser Air Bridge Light HS M12 (FCC)
Kvaser AB

The Kvaser Air Bridge Light HS M12 is a configuration-free wireless CAN bridge that uses a dust and water-tight M12 connector to connect CAN netwo...
View full details

$985

Sale
Sale

from $16

PCAN-miniPCIe connection cable to DB-9
PEAK-System Technik

PCAN-miniPCIe connection cable to DB-9Connects miniature connector on PCB of PEAK PCAN-miniPCIe cards to DB-9 IPEK-003020 = single CAN channel con...
View full details

from $16

Sale
Sale

$99

CANopen Chip CoC-100
SYS TEC electronic GmbH

Next Generation - the New CANopen Chip Like its predecessor, the sysWORXX CANopen Chip F40, the new sysWORXX CANopen Chip CoC-100 is a fully operat...
View full details

$99

Sale
Sale

$540

Memorator Light HS v2
Kvaser AB

Designed for troubleshooting any CAN-based (controller area network) system, the Kvaser Memorator Light HS v2 is an easy-to-use tool for logging se...
View full details

$540

Sale
Sold out

$369

SYS TEC USB-CANmodul2 (low&high speed)
SYS TEC electronic GmbH

The SYS TEC USB-CANmodul2 CAN-USB converter is an extended version of our USB-CANmodul1 and is designed to provide a highly flexible, yet cost-effi...
View full details

$369

Sold out
Sale

$2,080

Kvaser Memorator R SemiPro CAN Datalogger
Kvaser AB

This product is EOL as of Jan 2023. Please consider the Kvaser Memorator Pro 2xHS v2 or the Kvaser Memorator 2xHS v2 as the recommended replacement...
View full details

$2,080

Sale
Sale

$508

Kvaser PCIEcan HS
Kvaser AB

This product is EOL and not intended for new designs. Please consider the newer model, the Kvaser PCIEcan HS V2 with CAN FD support. The Kvaser PCI...
View full details

$508

Sale
Sale

$309

Kvaser OBD II Extension Cable 15 Meter
Kvaser AB

A Kvaser OBD II Extension Cable is an extension cable with a male to female OBD II connector. The cable is made of durable thermoplastic rubber. Al...
View full details

$309

Sale
Sale

$189

CANcrypt
Embedded Systems Academy

Commonly used security methods for authentication and encryption/decryption on the Internet cannot be easily applied to CAN/CANopen. ESAcademy's so...
View full details

$189

Sale
Sale

from $817

Kvaser U100P
Kvaser AB

The Kvaser U100P is the Precision version of Kvaser’s U100 range of CAN to USB interfaces. The Kvaser U100P delivers advanced features for engineer...
View full details

from $817

Sale
Sale

$1,319

Kvaser USBcan Pro 4xHS
Kvaser AB

The Kvaser USBcan Pro 4xHS is an advanced, portable multi-channel CAN/CAN FD to USB real time interface that handles transmission and reception of ...
View full details

$1,319

Sale
Sale

$59

Bus Fault Injection Board
MACH SYSTEMS

The Bus Fault Injection Board allows the user to inject faults into a physical layer of a differential network. The board can simulate errors: a wr...
View full details

$59

Sale
Sale

$749

PCAN MU-Thermocouple1 CAN FD
PEAK-System Technik

Configurable System for Data Acquisition and Data Processing The MU-Thermocouple1 CAN FD captures, processes, and transmits data via CAN FD. The te...
View full details

$749

Sale
Sale

from $279

PCAN-MicroMod FD Evaluation Board
PEAK-System Technik

Universal Evaluation Board for the Plug-in Module PCAN-MicroMod FD This product is an evaluation board for the PCAN-MicroMod FD and allows the conc...
View full details

from $279

Sale
Sale

$309

sysWORXX CANopen I/O-X2
SYS TEC electronic GmbH

The CANopen IO-X2 is a very compact and cost effective CANopen IO module featuring a high-density of industrial proven I/O's. The module includes a...
View full details

$309

Sale
Sale

$649

CANtouch: License for "Protocol Monitor CAN (Tx/Rx)"
GEMAC

License key to activate the "Protocol Monitor" feature of the GEMAC CANtouch mobile diagnostic device. It supports both Transmit and Receive of CAN...
View full details

$649

Sale
Sale

$859

Kvaser Leaf Pro HS V2 OBD2
Kvaser AB

Please consider either the Kvaser U100P-X3 or the Kvaser U100-X3 the replacement Kvaser's latest addition to the popular "Leaf" family brings prog...
View full details

$859

Sale
Sale

$1,649

Kvaser USBcan Pro 5xHS
Kvaser AB

This product is EOL as of Jan 2023. The new version is the Kvaser USBcan Pro 5xCAN. The Kvaser USBcan Pro 5xHS is a five channel, high performance...
View full details

$1,649

Sale
Sale

$408

Kvaser Mini PCI Express HS
Kvaser AB

(Not for new designs. The recommended replacement for this part is Mini PCIe 1xCAN (01368-1). The Kvaser Mini PCI Express HS is a highly-integrated...
View full details

$408

Sale