What is the warranty for Peak-System products?

Here is the complete hardware warranty section from the supplier. PCAN Adapter: PCAN-USB Adapter & PCAN-USB Adapter (Isolated)

I have a PCAN Adapter and have severed my cable to the service port on the engine. I am trying to confirm the wiring to the data link (from the CAN bus side).

These images show the pinout of the CAN bus side: Image 1 Image 2

Do you have a comparable product to Vector’s CANape and canoe/canalyzer?

You may want to look at the PCAN-USB Adapter with PCAN-Explorer 6 from PEAK. It will not be an exact 1:1 replacement, however.

Will the PCAN Adapter (2021, 2022, 4022, etc.) work with my [XYZ] device?

The PEAK PCAN-USB Adapter is a generic CAN interface for PC which allows CAN data exchange according to ISO 11898-2 with CAN bitrates of up to 1 Mbit/s. You will need to check if your devices also use a High-speed CAN connection per ISO 11898-2 standard. If they do, the chances are good that the PCAN-Adapter will work for you. We offer a 30-day money-back guarantee in the event it does not meet your needs.

What chips/circuitry are inside the PCAN USB Adapter?

The PCAN-USB Adapter has an FPGA with all the CAN controller circuitry, power supply circuits, and a CAN transceiver. For additional details, see the features section.

How does it handle 3.3 volt?

The PCAN-USB Adapter (IPEH-002021/22) will work with any CAN device that is ISO 11898-2 compliant. The adapter uses an NXP PCA82C251 CAN transceiver. Here is a link to the transceiver datasheet for full details on CAN voltages: PCA82C251 Datasheet

I ordered 3 PCAN USB adapters. If I want to connect two of them to talk to each other, and they are the only nodes on the CAN bus, what do I need to accomplish this?

You will need a terminated CAN cable such as our PCAN-Cable 2. Or something similar if you already have existing CAN cables. The DB-9 connector on the PCAN-USB Adapter is male. The cable has female connectors and the needed 120 Ohm termination resistors installed at both ends.

What chips/circuitry are inside the PCAN USB Adapter?

The PCAN-USB Adapter has an NXP CAN controller SJA1000 with 16 MHz clock frequency and an NXP CAN transceiver PCA82C251.

I am searching for a professional CAN Bus analyzer. We need the capability to monitor CAN Bus traffic and identify when message faults occur.

The PCAN-USB Adapter with PCAN-Explorer 6 software will serve your needs best!

I purchased the PCAN-USB Adapter (isolated). What else is required to record and then playback J1939 data?

The PCAN-Explorer V6 software with the J1939 add-in will work. We offer a 30-day trial with full functionality. Email us for your trial today.

I see the PCAN USB interface connects to a USB port, and the description says the interface is Linux compatible via SocketCAN. Does the driver present the socketCAN interface 'itself' (the USB interface being transparent), or will I have to provide the transport between the USB interface and the socketCAN interface?

The PEAK-System Linux page answers many of these questions and more. (SocketCAN is relevant for the SYSTEC USB-CANmodul from a different manufacturer.

I think the PCAN-USB Adapter (isolated) will work for the J1939 task I have. What do I need to be able to record and then playback that data?

The PCAN-Explorer V6 software with the J1939 add-in will work. PCAN-Explorer 6 Software

I purchased the PCAN-USB Adapter. Where can I download the driver for this USB adapter?

Windows and Linux drivers can be downloaded from the “Downloads” tab on the product page beneath the product description.

I have a IPEH-002262-KSM01. Do you have any example projects/files for this device? More than the examples provided in the manual?

The manufacturer has packaged all available files and demo projects into this download .

Is your CANopen Source Code UL (Underwriter Laboratories) certified?

No, our products are European, and CE certification is used for hardware, not software.

Can I download the software?

No, the process of getting the software ready and delivered via FTP transfer from SYSTEC usually takes one to two business days.

How do I set a custom CAN baud rate, for example, 333 kHz?

It is not possible to configure a CAN baud rate of exactly 333 kbit/s on the CAN-Ethernet Gateway V2. However, a baud rate of 333,333 kbit/s can be configured and has been tested. Please refer to the user's manual (section 6.4) for instructions on setting the gateway to this CAN baud rate.

Does the CANmodul1 require that a 120-ohm resistor be connected at the input port/CAN side?

Yes, a 120-ohm termination resistor is required at both ends of a CAN bus. If the CANmodul1 happens to be at the end, then an external bus termination is needed.

Will the CAN controller automatically determine whether it's a Standard or Extended ID?

Correct, no special settings are needed. The CAN controller automatically detects if it's 2.0A (11-bit identifier) or 2.0B (29-bit identifier) CAN specification.

What is the return policy?

Most unopened items in new condition and returned within 90 days will receive a refund or exchange. Some items have a modified return policy noted on the receipt or packing slip. Items that are opened or damaged or do not have a receipt may be denied a refund or exchange. Items purchased online or in-store may be returned to any store. Online purchases may be returned via a major parcel carrier. Click here to initiate a return.

How long does it take to process a refund?

We will reimburse you for returned items in the same way you paid for them. For example, any amounts deducted from a gift card will be credited back to a gift card. For returns by mail, once we receive your return, we will process it within 4–5 business days. It may take up to 7 days after we process the return to reflect in your account, depending on your financial institution's processing time.

What is the policy for late/non-delivery of items ordered online?

Our local teams work diligently to make sure that your order arrives on time, within our normaldelivery hours of 9AM to 8PM in the recipient's time zone. During busy holiday periods like Christmas, Valentine's and Mother's Day, we may extend our delivery hours before 9AM and after 8PM to ensure that all gifts are delivered on time. If for any reason your gift does not arrive on time, our dedicated Customer Service agents will do everything they can to help successfully resolve your issue. Click here to complete the form with your order-related question(s).

When will my credit card be charged?

We'll attempt to securely charge your credit card at the point of purchase online. If there's a problem, you'll be notified on the spot and prompted to use another card. Once we receive verification of sufficient funds, your payment will be completed and transferred securely to us. Your account will be charged in 24 to 48 hours.

Will I be charged sales tax for online orders?

Local and State sales tax will be collected if your recipient's mailing address is in: Arizona California Colorado

What software options do I need to purchase for the GEMAC CAN-Bus Tester 2?

There are 5 different add-on software licenses available. You will need one of the add-on licenses if you use a higher layer protocol such as CANopen, J1939, DeviceNet. There are also options for using a Protocol Monitor for one of these protocols. If you just use plain CAN, you may consider the Protocol Monitor CAN-License key for Protocol Monitor CAN (transmit / receive). The available licenses are as follows: CAN-Bus Tester 2: CANopen bus add-on $1039 CAN-Bus Tester 2: DeviceNet bus add-on $1239 CAN-Bus Tester 2: J1939 bus add-on $659 CAN-Bus Tester 2: Protocol Monitor CAN (Rx/Tx) $649 CAN-Bus Tester 2: Protocol Monitor CANopen (Receive) $519 CAN-Bus Tester 2: Protocol Monitor J1939 (Receive) $519

I'm looking at a GEMAC CAN-bus tester 2 for testing of CAN networks in our machines. Will I be able to debug the hardware side with the package by itself? What does the protocol monitor add-on do?

The protocol monitor does the following: CAN: Reception of CAN message frames incl. filtering, Transmission of CAN message frames and sequences (message lists) What level of testing do you plan to do? We're looking at debugging hardware issues with the network, would like to be able to determine problem messages/nodes on the network. I would recommend getting the protocol monitor license along with the CAN bus tester 2 device. Or you can buy the unit by itself first (available from stock) and see if you are okay without that license. You can always buy it at a later point.

What tools are available for developing a Windows-based CANopen application to talk to various CAN devices?

Phytools offers a number of different solutions for CANopen development on a Windows-based system. If you are looking for a full-featured CANopen source code package, we suggest the SYSTEC CANopen Source Code SO-877. This software is a full buyout license, meaning there will be no additional runtime fees or royalties for deployed products with this code inside. It can be used in combination with any SYSTEC CAN interface module. For developing PC-based applications in Windows, we recommend the CANopen Magic Pro DLL developed by our partner Embedded Systems Academy. This software works in combination with any PC-CAN interface made by PEAK-System Technik, such as their popular PCAN-USB Adapters. Embedded Systems Academy also has other CANopen network configuration tools that may be of interest. You can find more information on the Embedded Systems Academy page.

Are there any limitations to the CANopen Magic evaluation copy?

Yes, there are limitations to the CANopen Magic evaluation copy: 1. Communication with a real CAN bus is not possible. Instead, simulated CANopen nodes may be accessed over a purely internal CAN bus. 2. There is no command line interface to access the CAN bus. Please note: The features in this version match the full version of CANopen Magic Ultimate. There are other versions of CANopen Magic available with smaller feature sets. We hope you enjoy using this software and experimenting with CANopen!

Can I try this software before I purchase?

Yes, please email us for a 30-day PCAN Explorer Trial. You must also have a CAN interface, such as the PCAN USB Adapter. Each trial license includes all available add-in options.

I need a software program for collecting data off the J1939 Vehicle Network and parsing out each PGN and identifying which SPNs are available on the network and are changing in values to show it is valid data. What add-in or other product do I need to perform this?

You can do this with PCAN Explorer 6 with the J1939 add-in. We offer a 30-day trial of PCAN Explorer, and the trial comes with all the add-ins. Email us for your trial copy.

What is a .dbc file? (relevant for PCAN Explorer 6 - CANdb add-in)

A DBC file is a Communication Database for CAN. It is the distributed system's backbone. DBC files are basic text files that include information for decoding raw CAN bus data to physical values or in human-readable form. They specify which signals (e.g., RPM, Vehicle Speed, etc.) are contained within specific messages (i.e., CAN IDs). In developing a distributed ECU network based on CAN, a key component is the communication description in the form of DBC files. Described in DBC databases are the properties of the CAN network, the ECUs connected to the bus, and the CAN messages and signals.

My version of PCAN Trace (1.8.0.50) software is giving a bad file error message when trying to read my customers' 2.1 recordings. Can you help?

The PCAN-Trace can only handle trace files which comply with file version 1.x. A trace file that complies with version 2.x must be converted into file version 1.x with the 'PEAK-Converter.'

I am running PCAN Trace and collecting data off the J1939 Vehicle Network. I want to have a program that parses out each PGN and identifies which SPNs are available on the network and are changing in values to show it is valid data. What add-in or other product do I need to perform this?

PCAN Trace cannot do this, but you can do this with PCAN Explorer 6 with the J1939 add-in. We offer a 30-day trial of PCAN Explorer, and the trial comes with all the add-ins.

I am new to EtherCAT. I am looking for an EtherCAT Slave Unit that runs Linux on Raspberry Pi.

Yes, you can accomplish this with the Gateway Module Ethernet Slave coupled with the appropriate base RevPi module (IPC based on Raspberry Pi).

I need to convert two Modbus TCP devices to one Allen Bradley CompactLogix Ethernet IP. Questions I have are:

1. Hardware required. Looks like (1) KU-PR100066 and (1) KU-PR100088 would work? 2. Any additional hardware part number required to do this? 3. Can I convert both signals with one set of converters? A: The two gateway modules you inquired about (KU-PR100066 and KU-PR100088) will work to create a gateway system that connects Modbus TCP with Ethernet IP. The required connection clip is included. No additional items are needed.

Does the RevPi Core or Core 3 come with a power supply cable?

No, there is no cabling included with the RevPi Core or Core 3.

What are the mounting options for the RevPi Core or Core 3?

The RevPi Core or Core 3 can be mounted on a DIN rail housing (for DIN rail version EN 50022).

Does the RevPi Core or Core 3 come with an SD card?

No, there is no SD card included with the RevPi Core or Core 3. You can use a USB memory stick for data storage.

What are the graphics specs of the RevPi Core or Core 3? I need to drive a large LCD display.

The RevPi Core is based on the Broadcom BCM2711, quad-core Arm Cortex-A72. For more information, visit click here The RevPi Core 3 is based on the Broadcom BCM2837 processor. For more information, click here For more information on the VideoCore subsystem, see click here .

What are the limitations of the CANopen Magic evaluation?

The CANopen Magic evaluation has limitations. Please refer to the documentation and licensing information provided by Embedded Systems Academy, Inc.

What is the HS code for the following items: PCAN Cable 1 w/o termination, PCAN T-Adapter, PCAN-USB Adapter

The HTS code for cables and T-adapters is 8544429000. The PCAN-USB adapter is 8517620050. The ECCN number for all products is EAR99. All are manufactured in Germany.

How do I calculate the baud rate?

There is a tool made by PEAK for calculating the baud rate register settings: baudtool.zip

Are the SYS TEC Canmodul1 and the Kvaser Leaf Light v2 the same product essentially?

The two devices provide similar functionality in that they both connect a PC or laptop via its USB interface to a CAN bus. Both devices support the maximum CAN bitrate of 1 Mbit/s. However, both devices have unique designs in terms of internal circuitry and software API/drivers. There are other differences in terms of CAN message throughput, buffer size, etc. If you are using third-party software that specifically requires the use of the Kvaser Leaf Light V2, then I strongly advise against using a different type of USB-CAN interface.

I'm currently using the PCAN-USB to view 500k CAN bus data on cars. I would like to be able to view the LIN bus data on Chrysler vehicles 2011 and newer. Do I need a dedicated LIN interface or is there one that will do both LIN and CAN?

Phytools offers a PLIN-USB Adapter (dedicated LIN interface) and several interfaces that support both CAN and LIN, including the PCAN USB Pro FD, the Kvaser Hybrid, and the CAN FD LIN Gateway.

I am looking for an isolated CAN repeater, and I saw the one you have rated to 500V. Do you have any rated for higher voltages, around 1.5-2 kV?

The PCAN-Repeater DR establishes a galvanic isolation of up to 5 kV according to IEC60601-1 within a High-speed CAN bus. Both CAN ports are decoupled from each other and from the power supply. All message traffic, including error frames, is forwarded 1:1 between both ports. The PCAN-Repeater DR behaves passively and is transparent from the perspective of the CAN bus. LEDs display the current bus status.

I'm currently using the PCAN-USB Adapter to view 500k CAN bus data on cars. I would like to be able to view the LIN bus data on Chrysler vehicles 2011 and newer. Do I need a dedicated LIN interface or is there one that will do both LIN and CAN?

Phytools offers a PLIN-USB Adapter (dedicated LIN interface) and several interfaces that support both CAN and LIN, including the PCAN USB Pro FD, the Kvaser Hybrid, and the CAN FD LIN Gateway.

I am looking for the ability to connect two CAN FD channels and have the ability to process, manipulate, and filter CAN messages bidirectionally between each bus. Which products do I need?

There are two solutions: PC-based solution or a standalone solution. For the former, you can use PCAN-USB Pro FD Adapter, which has two independent CAN FD capable channels. Any message processing, manipulating, filtering, etc. will require using the corresponding PC software based on the PCAN Basic API. For the latter, use the PCAN Router FD with specially programmed firmware as a stand-alone CAN FD router.

I just need a simple CAN interface with some software that can receive and display CAN messages from other nodes as well as send CAN messages out to other nodes. What device would you recommend?

We suggest a PCAN-USB Interface with the included free PCAN-View software. If you need a device that is able to detect and analyze more of the physical layer properties of a CAN system, we do offer CAN diagnostic tools as well.

Manufacturers

Sort by

Show
24
36
48

View as

Sale

$239

PCAN USB Adapter
PEAK-System Technik

Shop the PCAN-USB Adapter from PEAK-System Technik to connect any laptop, computer or PC to a CAN bus via USB, facilitating the monitoring and reco...
View full details

$239

Sale
Sale

$296

PCAN USB Adapter (isolated)
PEAK-System Technik

This PCAN adapter makes it possible to connect any PC with a USB slot into a CAN network. Galvanic isolation of up to 500V between the CAN signals ...
View full details

$296

Sale
Sale

$334

Kvaser Leaf Light HS v2
Kvaser AB

The sleek and ergonomically designed Kvaser Leaf Light V2 represents one of the most cost-efficient and easy ways of connecting a laptop or desktop...
View full details

$334

Sale
Sale

$259

SYS TEC USB-CANmodul1 (single CAN, opto-isolated)
SYS TEC electronic GmbH

The SYS TEC CAN USB Adapter, the USB-CANmodul1, is a compact and cost-effective CAN-bus interface for connecting a CAN bus network to a PC via a US...
View full details

$259

Sale
Sale

$832

PCAN-Explorer 6 Portable License
PEAK-System Technik

CAN/CANFD Network Monitoring SoftwarePortable License with Copy Protection Dongle (Request free 30 day trial) PCAN-Explorer 6 Windows software is...
View full details

$832

Sale
Sale

$1,422

Kvaser Memorator Pro 2xHS V2
Kvaser AB

Professional dual-channel standalone data logger and USB to CAN interface with t-Program. Kvaser Memorator Pro 2xHS v2 is a professional-level, pro...
View full details

$1,422

Sale
Sale

from $307

PCAN-miniPCIe card, iso (1ch/2ch)
PEAK-System Technik

The new CAN FD adapter from PEAK-System PCAN-USB FD allows the connection of CAN FD and classic CAN networks to a computer via USB. The simple han...
View full details

from $307

Sale
Sale

$347

PCAN-USB FD Adapter
PEAK-System Technik

The new CAN FD adapter from PEAK-System PCAN-USB FD allows the connection of CAN FD and classic CAN networks to a computer via USB. The simple hand...
View full details

$347

Sale
Sale

$18

PCAN-MiniTerm
PEAK-System Technik

Miniature CAN Termination Adapter The PCAN-MiniTerm adapter terminates a high-speed CAN bus (ISO 11898-2) at one end. It is used if a CAN node is c...
View full details

$18

Sale
Sale

$354

PCAN-Ethernet Gateway DR
PEAK-System Technik

The PCAN-Ethernet Gateway DR allows the connection of different CAN busses over IP networks. CAN frames are wrapped in TCP or UDP message packets...
View full details

$354

Sale
Sale

$708

PCAN-USB Pro FD Adapter
PEAK-System Technik

The new CAN FD Pro from PEAK-System, PCAN-USB Pro FD adapter enables the connection of CAN FD and LIN networks to a computer via USB. Two field bus...
View full details

$708

Sale
Sale

from $62

PCAN SAE J1939 Cable
PEAK-System Technik

The SAE J1939 cable establishes consistent CAN messages for the communication and diagnosis between components of heavy-duty vehicles such as const...
View full details

from $62

Sale
Sale

$250

PLIN-USB Adapter
PEAK-System Technik

The PLIN-USB enables a Windows computer to be connected to a LIN network via USB. The adapter supports the LIN protocol in accordance with the ISO ...
View full details

$250

Sale
Sale

$22

PCAN Termination Adapter
PEAK-System Technik

CAN Termination Adapter The PCAN-Term adapter terminates a high-speed CAN bus (ISO 11898-2) at one end. It is used if a CAN node is connected witho...
View full details

$22

Sale
Sale

from $23

PCAN T-Adapter
PEAK-System Technik

T-Adapter for CAN Tapping The PCAN-T-Adapter and PCAN-Mini-T-Adapter create a tap connection to the data cables and the ground within a CAN bus in ...
View full details

from $23

Sale
Sale

$126

PCAN Explorer 6 - CANdb add-in
PEAK-System Technik

Optional Function Upgrades for PCAN-Explorer V6 Note: Please provide your PCAN Explorer 6 original License Id in the notes section of the checkou...
View full details

$126

Sale
Sale

from $275

PCAN-PCI Express Insert-card (1ch/2ch)
PEAK-System Technik

The PCAN-PCI Express card enables the connection of a PC with PCI Express slots to CAN networks. Configuration of the host PC is not necessary sinc...
View full details

from $275

Sale
Sale

$69

PCAN Cable OBD-2 to SUB-D
PEAK-System Technik

CAN-OBD-2 Diagnostics Cable Many modern motor vehicles have an OBD-2 interface for connecting various diagnostics and testing tools. This adapter c...
View full details

$69

Sale
Sale

$31

PCAN Cable 2 w/ 120 Ohm termination
PEAK-System Technik

PCAN Cable 2 with two 120 Ohm CAN bus termination resistors These cables are needed to set up a CAN bus and are specially designed to be used in a ...
View full details

$31

Sale
Sale

$125

Optical CAN Bus Adapter (PCAN-Optoadapter)
PEAK-System Technik

The PCAN-Optoadapter is a universal plug-in adapter to allow galvanic isolation of High-speed CAN bus systems.Its integrated logic means that dec...
View full details

$125

Sale
Sale

$699

PCAN-Explorer 6 Software
PEAK-System Technik

CAN Network Monitoring SoftwareSingle Computer License (Portable license also available) The new PCAN-Explorer 6 developed by PEAK-System Technik...
View full details

$699

Sale
Sale

from $1,128

PCAN-USB X6 Adapter
PEAK-System Technik

The new 6-channel CAN FD adapter from PEAK-System, PCAN-USB X6, enables the connection of CAN FD and classic CAN networks to a computer via a singl...
View full details

from $1,128

Sale
Sale

$335

PCAN-Repeater
PEAK-System Technik

The PCAN-Repeater made by PEAK System Technik creates a connection between two high-speed CAN busses with galvanic isolation of up to 5 kV. Each CA...
View full details

$335

Sale
Sale

$209

RevPi DIO Module
KUNBUS

To transform the Kunbus Revolution Pi into an industrial control unit, various digital I/O modules can be connected to the base module RevPi Core. ...
View full details

$209

Sale
Sale

from $331

PCAN-M.2
PEAK-System Technik

The PCAN-M.2 connects CAN and CAN FD networks to a computer board via its M.2 interface (PCIe). With its small form factor, the plug-in card is opt...
View full details

from $331

Sale
Sale

$213

PCAN-Panel plug-in for PCAN Explorer 6
PEAK-System Technik

Optional Function Upgrades for PCAN-Explorer V6 Note: Please provide your PCAN Explorer 6 original License Id in the notes section of the checkout ...
View full details

$213

Sale
Sale

$213

PCAN-Plotter plug-in for PCAN Explorer 6
PEAK-System Technik

Optional Function Upgrades for PCAN-Explorer V6 Note: Please provide your PCAN Explorer 6 original License Id in the notes section of the checkout ...
View full details

$213

Sale
Sale

$26

PCAN Cable 1 w/o termination
PEAK-System Technik

PCAN Cable 1 without CAN bus termination These cables are needed to set up a CAN bus and are specially designed to be used in a CAN environment. If...
View full details

$26

Sale
Sale

$35

PCAN-Cable 3
PEAK-System Technik

CAN Cable for Test and Measurement Setups With this cable the two components CAN-High and CAN-Low of the differential CAN signal can be picked up f...
View full details

$35

Sale
Sold out

$284

RevPi Core 3 (EOL)
KUNBUS

This product is EOL. Please consider the newer versions instead. The heart of the revolution RevPi Core 3 is the latest version of the RevPi Core, ...
View full details

$284

Sold out
Sold out

from $289

RevPi Core 3+
KUNBUS

This item has been updated to a newer version. A Robust Open Source IPC Based on Raspberry Pi The powerful RevPi Core 3+ was created for those ne...
View full details

from $289

Sold out
Sale

$17

PCAN-D-Sub Connection Adapter
PEAK-System Technik

A number of PEAK-System CAN hardware products in DIN rail housing feature a 4-pin screw terminal block as CAN connector. The PCAN-D-Sub Connection ...
View full details

$17

Sale
Sale

$416

PCAN Explorer 6 - J1939 add-in
PEAK-System Technik

Communication on a CAN bus in utility vehicles for the transmission of diagnostics data and control information is describes in the SAE J1939 netwo...
View full details

$416

Sale
Sale

$336

PCAN-LIN Interface (high-speed CAN)
PEAK-System Technik

The PCAN-LIN module enables users to communicate over CAN, LIN and serial interface. The module is supplied in a plastic casing. The included firmw...
View full details

$336

Sale
Sale

$389

RevPi Analog-IO Module
KUNBUS

Expanding the RevPI Core functionality to process analog I/O signals is now possible with the help of the new RevPi AIO module. This add-on unit fe...
View full details

$389

Sale
Sale

$369

SYS TEC USB-CANmodul2 (dual CAN, opto-isolated)
SYS TEC electronic GmbH

The SYS TEC USB-CANmodul2 CAN-USB converter is an extended version of our single-channel USB-CANmodul and is designed to provide a most flexible, y...
View full details

$369

Sale
Sale

from $348

PCAN-miniPCIe FD card, iso (1ch/2ch/4ch)
PEAK-System Technik

The PCAN-miniPCIe FD card made by PEAK-System Technik (Germany) provides an easy way to connect an embedded PC or laptop with a PCI Express Mini sl...
View full details

from $348

Sale
Sale

$345

Kvaser Leaf Light HS v2 J1939-13 Type II
Kvaser AB

Kvaser's Leaf Light HS V2 J1939-13 Type II is the latest version of Kvaser's popular line of Leaf Light V2 USB-to-CAN interfaces. This application ...
View full details

$345

Sale
Sale

from $317

PCAN-PCI Express FD (1ch/2ch/4ch)
PEAK-System Technik

The PCAN-PCI Express FD plug-in card made by PEAK System Technik allows the connection of a PC with PCI Express slots to CAN FD and CAN networks. T...
View full details

from $317

Sale
Sale

$568

Kvaser USBcan Light 2xHS
Kvaser AB

The Kvaser USBcan Light 2xHS is a compact, reliable and cost-effective means of connecting two high speed CAN busses to a PC or mobile computer. Wi...
View full details

$568

Sale
Sale

$742

Kvaser USBcan Light 4xHS
Kvaser AB

The compact and reliable Kvaser USBcan Light 4xHS is a cost-effective means of connecting four high-speed CAN buses to a PC or mobile computer. Thi...
View full details

$742

Sale
Sale

$173

PCAN-AU5790
PEAK-System Technik

The PCAN-AU5790 bus converter establishes a connection between a High-speed CAN bus (ISO 11898-2) and a Single-wire CAN bus (SAE J2411). One of the...
View full details

$173

Sale
Sale

$8

PCAN-Adapter D-Sub to Screw Terminals
PEAK-System Technik

The adapter with a D-Sub socket connector and a three-pin screw terminal block allows easy connection of open cable ends of a CAN bus to a D-Sub co...
View full details

$8

Sale
Sale

$782

PCAN-Router Pro
PEAK-System Technik

The PCAN-Router Pro allows the data traffic from up to four High-speed CAN buses to be connected together. Besides straight message forwarding, the...
View full details

$782

Sale
Sale

$89

LabView Driver for PCAN-Basic 4.x
KDI Digital Instrumentation

LabVIEW® API for PCAN© BASIC FD 4.0 The LabVIEW® API uses the PCAN© Basic 4.0 API from PEAK-System. It allows you to exchange CAN messages via CAN ...
View full details

$89

Sale
Sale

$187

PCAN-RS-232
PEAK-System Technik

The PEAK PCAN-RS-232 is a programmable module for the communication between RS-232 and CAN. The device is based on the NXP LPC21 series microcontro...
View full details

$187

Sale
Sale

$759

Kvaser Hybrid 2xCAN/LIN
Kvaser AB

Kvaser Hybrid 2xCAN/LIN is a flexible, dual channel interface that allows each channel to be assigned independently as CAN or LIN. This makes the K...
View full details

$759

Sale
Sale

$25

Kvaser D-sub 9 pin 120 Ohm termination adapter
Kvaser AB

Termination Adapter for CANbus The Kvaser D-sub 9 pin 120 Ohm termination adapter is a CANbus adaptor with a 9-pin male D-Sub connector at one end ...
View full details

$25

Sale