What is the warranty for Peak-System products?

Here is the complete hardware warranty section from the supplier. PCAN Adapter: PCAN-USB Adapter & PCAN-USB Adapter (Isolated)

I have a PCAN Adapter and have severed my cable to the service port on the engine. I am trying to confirm the wiring to the data link (from the CAN bus side).

These images show the pinout of the CAN bus side: Image 1 Image 2

Do you have a comparable product to Vector’s CANape and canoe/canalyzer?

You may want to look at the PCAN-USB Adapter with PCAN-Explorer 6 from PEAK. It will not be an exact 1:1 replacement, however.

Will the PCAN Adapter (2021, 2022, 4022, etc.) work with my [XYZ] device?

The PEAK PCAN-USB Adapter is a generic CAN interface for PC which allows CAN data exchange according to ISO 11898-2 with CAN bitrates of up to 1 Mbit/s. You will need to check if your devices also use a High-speed CAN connection per ISO 11898-2 standard. If they do, the chances are good that the PCAN-Adapter will work for you. We offer a 30-day money-back guarantee in the event it does not meet your needs.

What chips/circuitry are inside the PCAN USB Adapter?

The PCAN-USB Adapter has an FPGA with all the CAN controller circuitry, power supply circuits, and a CAN transceiver. For additional details, see the features section.

How does it handle 3.3 volt?

The PCAN-USB Adapter (IPEH-002021/22) will work with any CAN device that is ISO 11898-2 compliant. The adapter uses an NXP PCA82C251 CAN transceiver. Here is a link to the transceiver datasheet for full details on CAN voltages: PCA82C251 Datasheet

I ordered 3 PCAN USB adapters. If I want to connect two of them to talk to each other, and they are the only nodes on the CAN bus, what do I need to accomplish this?

You will need a terminated CAN cable such as our PCAN-Cable 2. Or something similar if you already have existing CAN cables. The DB-9 connector on the PCAN-USB Adapter is male. The cable has female connectors and the needed 120 Ohm termination resistors installed at both ends.

What chips/circuitry are inside the PCAN USB Adapter?

The PCAN-USB Adapter has an NXP CAN controller SJA1000 with 16 MHz clock frequency and an NXP CAN transceiver PCA82C251.

I am searching for a professional CAN Bus analyzer. We need the capability to monitor CAN Bus traffic and identify when message faults occur.

The PCAN-USB Adapter with PCAN-Explorer 6 software will serve your needs best!

I purchased the PCAN-USB Adapter (isolated). What else is required to record and then playback J1939 data?

The PCAN-Explorer V6 software with the J1939 add-in will work. We offer a 30-day trial with full functionality. Email us for your trial today.

I see the PCAN USB interface connects to a USB port, and the description says the interface is Linux compatible via SocketCAN. Does the driver present the socketCAN interface 'itself' (the USB interface being transparent), or will I have to provide the transport between the USB interface and the socketCAN interface?

The PEAK-System Linux page answers many of these questions and more. (SocketCAN is relevant for the SYSTEC USB-CANmodul from a different manufacturer.

I think the PCAN-USB Adapter (isolated) will work for the J1939 task I have. What do I need to be able to record and then playback that data?

The PCAN-Explorer V6 software with the J1939 add-in will work. PCAN-Explorer 6 Software

I purchased the PCAN-USB Adapter. Where can I download the driver for this USB adapter?

Windows and Linux drivers can be downloaded from the “Downloads” tab on the product page beneath the product description.

I have a IPEH-002262-KSM01. Do you have any example projects/files for this device? More than the examples provided in the manual?

The manufacturer has packaged all available files and demo projects into this download .

Is your CANopen Source Code UL (Underwriter Laboratories) certified?

No, our products are European, and CE certification is used for hardware, not software.

Can I download the software?

No, the process of getting the software ready and delivered via FTP transfer from SYSTEC usually takes one to two business days.

How do I set a custom CAN baud rate, for example, 333 kHz?

It is not possible to configure a CAN baud rate of exactly 333 kbit/s on the CAN-Ethernet Gateway V2. However, a baud rate of 333,333 kbit/s can be configured and has been tested. Please refer to the user's manual (section 6.4) for instructions on setting the gateway to this CAN baud rate.

Does the CANmodul1 require that a 120-ohm resistor be connected at the input port/CAN side?

Yes, a 120-ohm termination resistor is required at both ends of a CAN bus. If the CANmodul1 happens to be at the end, then an external bus termination is needed.

Will the CAN controller automatically determine whether it's a Standard or Extended ID?

Correct, no special settings are needed. The CAN controller automatically detects if it's 2.0A (11-bit identifier) or 2.0B (29-bit identifier) CAN specification.

What is the return policy?

Most unopened items in new condition and returned within 90 days will receive a refund or exchange. Some items have a modified return policy noted on the receipt or packing slip. Items that are opened or damaged or do not have a receipt may be denied a refund or exchange. Items purchased online or in-store may be returned to any store. Online purchases may be returned via a major parcel carrier. Click here to initiate a return.

How long does it take to process a refund?

We will reimburse you for returned items in the same way you paid for them. For example, any amounts deducted from a gift card will be credited back to a gift card. For returns by mail, once we receive your return, we will process it within 4–5 business days. It may take up to 7 days after we process the return to reflect in your account, depending on your financial institution's processing time.

What is the policy for late/non-delivery of items ordered online?

Our local teams work diligently to make sure that your order arrives on time, within our normaldelivery hours of 9AM to 8PM in the recipient's time zone. During busy holiday periods like Christmas, Valentine's and Mother's Day, we may extend our delivery hours before 9AM and after 8PM to ensure that all gifts are delivered on time. If for any reason your gift does not arrive on time, our dedicated Customer Service agents will do everything they can to help successfully resolve your issue. Click here to complete the form with your order-related question(s).

When will my credit card be charged?

We'll attempt to securely charge your credit card at the point of purchase online. If there's a problem, you'll be notified on the spot and prompted to use another card. Once we receive verification of sufficient funds, your payment will be completed and transferred securely to us. Your account will be charged in 24 to 48 hours.

Will I be charged sales tax for online orders?

Local and State sales tax will be collected if your recipient's mailing address is in: Arizona California Colorado

What software options do I need to purchase for the GEMAC CAN-Bus Tester 2?

There are 5 different add-on software licenses available. You will need one of the add-on licenses if you use a higher layer protocol such as CANopen, J1939, DeviceNet. There are also options for using a Protocol Monitor for one of these protocols. If you just use plain CAN, you may consider the Protocol Monitor CAN-License key for Protocol Monitor CAN (transmit / receive). The available licenses are as follows: CAN-Bus Tester 2: CANopen bus add-on $1039 CAN-Bus Tester 2: DeviceNet bus add-on $1239 CAN-Bus Tester 2: J1939 bus add-on $659 CAN-Bus Tester 2: Protocol Monitor CAN (Rx/Tx) $649 CAN-Bus Tester 2: Protocol Monitor CANopen (Receive) $519 CAN-Bus Tester 2: Protocol Monitor J1939 (Receive) $519

I'm looking at a GEMAC CAN-bus tester 2 for testing of CAN networks in our machines. Will I be able to debug the hardware side with the package by itself? What does the protocol monitor add-on do?

The protocol monitor does the following: CAN: Reception of CAN message frames incl. filtering, Transmission of CAN message frames and sequences (message lists) What level of testing do you plan to do? We're looking at debugging hardware issues with the network, would like to be able to determine problem messages/nodes on the network. I would recommend getting the protocol monitor license along with the CAN bus tester 2 device. Or you can buy the unit by itself first (available from stock) and see if you are okay without that license. You can always buy it at a later point.

What tools are available for developing a Windows-based CANopen application to talk to various CAN devices?

Phytools offers a number of different solutions for CANopen development on a Windows-based system. If you are looking for a full-featured CANopen source code package, we suggest the SYSTEC CANopen Source Code SO-877. This software is a full buyout license, meaning there will be no additional runtime fees or royalties for deployed products with this code inside. It can be used in combination with any SYSTEC CAN interface module. For developing PC-based applications in Windows, we recommend the CANopen Magic Pro DLL developed by our partner Embedded Systems Academy. This software works in combination with any PC-CAN interface made by PEAK-System Technik, such as their popular PCAN-USB Adapters. Embedded Systems Academy also has other CANopen network configuration tools that may be of interest. You can find more information on the Embedded Systems Academy page.

Are there any limitations to the CANopen Magic evaluation copy?

Yes, there are limitations to the CANopen Magic evaluation copy: 1. Communication with a real CAN bus is not possible. Instead, simulated CANopen nodes may be accessed over a purely internal CAN bus. 2. There is no command line interface to access the CAN bus. Please note: The features in this version match the full version of CANopen Magic Ultimate. There are other versions of CANopen Magic available with smaller feature sets. We hope you enjoy using this software and experimenting with CANopen!

Can I try this software before I purchase?

Yes, please email us for a 30-day PCAN Explorer Trial. You must also have a CAN interface, such as the PCAN USB Adapter. Each trial license includes all available add-in options.

I need a software program for collecting data off the J1939 Vehicle Network and parsing out each PGN and identifying which SPNs are available on the network and are changing in values to show it is valid data. What add-in or other product do I need to perform this?

You can do this with PCAN Explorer 6 with the J1939 add-in. We offer a 30-day trial of PCAN Explorer, and the trial comes with all the add-ins. Email us for your trial copy.

What is a .dbc file? (relevant for PCAN Explorer 6 - CANdb add-in)

A DBC file is a Communication Database for CAN. It is the distributed system's backbone. DBC files are basic text files that include information for decoding raw CAN bus data to physical values or in human-readable form. They specify which signals (e.g., RPM, Vehicle Speed, etc.) are contained within specific messages (i.e., CAN IDs). In developing a distributed ECU network based on CAN, a key component is the communication description in the form of DBC files. Described in DBC databases are the properties of the CAN network, the ECUs connected to the bus, and the CAN messages and signals.

My version of PCAN Trace (1.8.0.50) software is giving a bad file error message when trying to read my customers' 2.1 recordings. Can you help?

The PCAN-Trace can only handle trace files which comply with file version 1.x. A trace file that complies with version 2.x must be converted into file version 1.x with the 'PEAK-Converter.'

I am running PCAN Trace and collecting data off the J1939 Vehicle Network. I want to have a program that parses out each PGN and identifies which SPNs are available on the network and are changing in values to show it is valid data. What add-in or other product do I need to perform this?

PCAN Trace cannot do this, but you can do this with PCAN Explorer 6 with the J1939 add-in. We offer a 30-day trial of PCAN Explorer, and the trial comes with all the add-ins.

I am new to EtherCAT. I am looking for an EtherCAT Slave Unit that runs Linux on Raspberry Pi.

Yes, you can accomplish this with the Gateway Module Ethernet Slave coupled with the appropriate base RevPi module (IPC based on Raspberry Pi).

I need to convert two Modbus TCP devices to one Allen Bradley CompactLogix Ethernet IP. Questions I have are:

1. Hardware required. Looks like (1) KU-PR100066 and (1) KU-PR100088 would work? 2. Any additional hardware part number required to do this? 3. Can I convert both signals with one set of converters? A: The two gateway modules you inquired about (KU-PR100066 and KU-PR100088) will work to create a gateway system that connects Modbus TCP with Ethernet IP. The required connection clip is included. No additional items are needed.

Does the RevPi Core or Core 3 come with a power supply cable?

No, there is no cabling included with the RevPi Core or Core 3.

What are the mounting options for the RevPi Core or Core 3?

The RevPi Core or Core 3 can be mounted on a DIN rail housing (for DIN rail version EN 50022).

Does the RevPi Core or Core 3 come with an SD card?

No, there is no SD card included with the RevPi Core or Core 3. You can use a USB memory stick for data storage.

What are the graphics specs of the RevPi Core or Core 3? I need to drive a large LCD display.

The RevPi Core is based on the Broadcom BCM2711, quad-core Arm Cortex-A72. For more information, visit click here The RevPi Core 3 is based on the Broadcom BCM2837 processor. For more information, click here For more information on the VideoCore subsystem, see click here .

What are the limitations of the CANopen Magic evaluation?

The CANopen Magic evaluation has limitations. Please refer to the documentation and licensing information provided by Embedded Systems Academy, Inc.

What is the HS code for the following items: PCAN Cable 1 w/o termination, PCAN T-Adapter, PCAN-USB Adapter

The HTS code for cables and T-adapters is 8544429000. The PCAN-USB adapter is 8517620050. The ECCN number for all products is EAR99. All are manufactured in Germany.

How do I calculate the baud rate?

There is a tool made by PEAK for calculating the baud rate register settings: baudtool.zip

Are the SYS TEC Canmodul1 and the Kvaser Leaf Light v2 the same product essentially?

The two devices provide similar functionality in that they both connect a PC or laptop via its USB interface to a CAN bus. Both devices support the maximum CAN bitrate of 1 Mbit/s. However, both devices have unique designs in terms of internal circuitry and software API/drivers. There are other differences in terms of CAN message throughput, buffer size, etc. If you are using third-party software that specifically requires the use of the Kvaser Leaf Light V2, then I strongly advise against using a different type of USB-CAN interface.

I'm currently using the PCAN-USB to view 500k CAN bus data on cars. I would like to be able to view the LIN bus data on Chrysler vehicles 2011 and newer. Do I need a dedicated LIN interface or is there one that will do both LIN and CAN?

Phytools offers a PLIN-USB Adapter (dedicated LIN interface) and several interfaces that support both CAN and LIN, including the PCAN USB Pro FD, the Kvaser Hybrid, and the CAN FD LIN Gateway.

I am looking for an isolated CAN repeater, and I saw the one you have rated to 500V. Do you have any rated for higher voltages, around 1.5-2 kV?

The PCAN-Repeater DR establishes a galvanic isolation of up to 5 kV according to IEC60601-1 within a High-speed CAN bus. Both CAN ports are decoupled from each other and from the power supply. All message traffic, including error frames, is forwarded 1:1 between both ports. The PCAN-Repeater DR behaves passively and is transparent from the perspective of the CAN bus. LEDs display the current bus status.

I'm currently using the PCAN-USB Adapter to view 500k CAN bus data on cars. I would like to be able to view the LIN bus data on Chrysler vehicles 2011 and newer. Do I need a dedicated LIN interface or is there one that will do both LIN and CAN?

Phytools offers a PLIN-USB Adapter (dedicated LIN interface) and several interfaces that support both CAN and LIN, including the PCAN USB Pro FD, the Kvaser Hybrid, and the CAN FD LIN Gateway.

I am looking for the ability to connect two CAN FD channels and have the ability to process, manipulate, and filter CAN messages bidirectionally between each bus. Which products do I need?

There are two solutions: PC-based solution or a standalone solution. For the former, you can use PCAN-USB Pro FD Adapter, which has two independent CAN FD capable channels. Any message processing, manipulating, filtering, etc. will require using the corresponding PC software based on the PCAN Basic API. For the latter, use the PCAN Router FD with specially programmed firmware as a stand-alone CAN FD router.

I just need a simple CAN interface with some software that can receive and display CAN messages from other nodes as well as send CAN messages out to other nodes. What device would you recommend?

We suggest a PCAN-USB Interface with the included free PCAN-View software. If you need a device that is able to detect and analyze more of the physical layer properties of a CAN system, we do offer CAN diagnostic tools as well.

PEAK-System Technik

A leading provider of CAN hardware, software, and services, PEAK-Systems Technik supports you in your CAN FD, Classic CAN and LIN communication needs. Founded in 1999, PEAK-System Technik specializes in fieldbuses CAN and LIN for the automotive, engineering and industrial communication sectors.

PC to CAN Interfaces

PCAN-USB and PLIN-USB adapters for conventional PC interfaces and embedded applications supporting High-speed USB 2.0, as well as PCI-Express, mini PCI-Express, and M.2 interfaces
I/O modules with CAN/CAN FD connection for control, measured data recording, and processing
Routers and gateways for the forwarding of messages between CAN buses and other networks
Data loggers and diagnostic hardware

CAN Software

CAN development software for Windows® 11, 10, 8.1 (32/64-bit) and Linux
CAN analyzing software for Windows® 11, 10, 8.1 (32/64-bit) and Linux
Applications for recording, playback, and simulation of message traffic
Programming interfaces for various protocols and standards

CAN Accessories

CAN connection cables for various applications (DB-9, OBD-2, J1939, M12)
CAN bus converters and decouplers

PEAK-System Technik is certified per ISO 9001:2015 Certificate and ISO 14001:2015 Certificate. Check out PEAK's complete product catalog . Click here for a complete list of firmware, data sheets, drivers, etc. PEAK has been a pioneer in the introduction of the new CAN FD standard offering the first CAN FD to USB adapter hardware on the market. Now almost all of PEAK's products are available with CAN FD support.

PEAK-System Quality and Environment

PEAK-System Technik is certified according to the international standards ISO 9001:2015 and ISO 14001:2015. The management system combines the requirements of the standard ISO 9001 for quality management systems and the ones of the standard ISO 14001 for environmental management systems.

PEAK-System Scope of Certification

Peak-System Technik specializes in the development, manufacturing and sales of hardware and software for applications in the mobile and industrial communication sector. Click here for all certificates including RoHS 2, Conflict Minerals, and REACH regulation.

Sort by

Show
24
36
48

View as

Sale

$20

PCAN Termination Adapter
PEAK-System Technik

CAN Termination Adapter The PCAN-Term adapter terminates a high-speed CAN bus (ISO 11898-2) at one end. It is used if a CAN node is connected witho...
View full details

$20

Sale
Sale

from $979

PCAN-LWL
PEAK-System Technik

Coupling for optical transmission of CAN and CAN FD data For use in explosion-proof areas or for EMI/EMC measurements, the PCAN-LWL can be used to ...
View full details

from $979

Sale
Sale

from $21

PCAN T-Adapter
PEAK-System Technik

T-Adapter for CAN Tapping The PCAN-T-Adapter and PCAN-Mini-T-Adapter create a tap connection to the data cables and the ground within a CAN bus in ...
View full details

from $21

Sale
Sale

from $275

PCAN-PCI Express Insert-card (1ch/2ch)
PEAK-System Technik

The PCAN-PCI Express card enables the connection of a PC with PCI Express slots to CAN networks. Configuration of the host PC is not necessary sinc...
View full details

from $275

Sale
Sale

$369

PCAN-Router w/ D-Sub
PEAK-System Technik

The PCAN-Router is a dual-channel CAN module with an NXP LPC21 series programmable microcontroller. This CAN router provides the option of using th...
View full details

$369

Sale
Sale

$34

PCAN-Cable 3
PEAK-System Technik

CAN Cable for Test and Measurement Setups With this cable the two components CAN-High and CAN-Low of the differential CAN signal can be picked up f...
View full details

$34

Sale
Sale

$699

PCAN MU-Thermocouple1 CAN
PEAK-System Technik

Configurable System for Data Acquisition and Data Processing The Thermocouple Measuring Unit offers connections for 8 thermo-elements for different...
View full details

$699

Sale
Sale

$15

PCAN-D-Sub Connection Adapter
PEAK-System Technik

A number of PEAK-System CAN hardware products in DIN rail housing feature a 4-pin screw terminal block as CAN connector. The PCAN-D-Sub Connection ...
View full details

$15

Sale
Sale

$180

PCAN-RS-232
PEAK-System Technik

The PEAK PCAN-RS-232 is a programmable module for the communication between RS-232 and CAN. The device is based on the NXP LPC21 series microcontro...
View full details

$180

Sale
Sale

$379

PCAN-Trace Data Logger
PEAK-System Technik

Comprehensive CAN Data Logger from PEAK The PEAK PCAN-Trace program is a data logger which is capable to record up to 9,999,000 CAN messages. All m...
View full details

$379

Sale
Sale

$399

PCAN-MicroMod Analog 2
PEAK-System Technik

Please note: The product is only available in smaller quantities. Unfortunately, larger quantities can no longer be produced. Please see the PCAN M...
View full details

$399

Sale
Sale

$343

PCAN-GPS
PEAK-System Technik

The PCAN-GPS made by PEAK-System Technik (Germany) is a programmable sensor module for position and orientation determination. The unit has a satel...
View full details

$343

Sale
Sale

$449

PCAN-Wireless Gateway
PEAK-System Technik

The PCAN-Wireless Gateway allows the connection of different CAN busses over IP networks. CAN frames are wrapped in TCP or UDP message packets and ...
View full details

$449

Sale
Sale

$49

LIN Connection Cable for PCAN-LIN
PEAK-System Technik

Pre-configured Cable Set for the PCAN-LIN Module The field buses and the power supply on the PCAN-LIN module are connected together via a D-Sub plu...
View full details

$49

Sale
Sale

$447

PCAN-MiniDisplay
PEAK-System Technik

The PCAN-MiniDisplay made by PEAK-System Technik is product that serves as a human-machine interface (HMI) for the visualization of CAN data. Both ...
View full details

$447

Sale
Sale

$0

PCAN-RP1210 API
PEAK-System Technik

The Recommended Practice 1210 was defined by the Technology and Maintenance Council (TMC) as a standardized API for communication between Windows® ...
View full details

$0

Sale
Sale

$289

PCAN-MicroMod Analog 1
PEAK-System Technik

Please note: The product is only available in smaller quantities. Unfortunately, larger quantities can no longer be produced. Please see the PCAN M...
View full details

$289

Sale
Sale

$0

PCAN-View (Free CAN/CAN FD Monitor)
PEAK-System Technik

Windows® Software for Displaying CAN and CAN FD Messages PCAN-View is a straightforward CAN monitor software for Windows. It enables users to view...
View full details

$0

Sale
Sale

from $293

PCAN-PCI insert-card iso (1ch/2ch)
PEAK-System Technik

The PCAN-PCI insert-card serves as an easy-to-use and cost-effective solution for connection of a CAN bus to a PC via a 9-pin SUB-D plug. The pin a...
View full details

from $293

Sale
Sale

$289

PCAN-MicroMod Digital 2
PEAK-System Technik

Please note: The product is only available in smaller quantities. Unfortunately, larger quantities can no longer be produced. Please see the PCAN M...
View full details

$289

Sale
Sale

$55

LIN Connection Cable for PCAN-USB Pro FD
PEAK-System Technik

Pre-configured Cable Set for the PCAN-USB Pro FD Adapter PEAK's PCAN-USB Pro FD and PCAN-USB Pro Adapters route the signals for the two field buses...
View full details

$55

Sale
Sale

from $355

PCAN-PCI/104 Express card, iso (1ch/2ch)
PEAK-System Technik

The PCAN-PCI/104-Express card enables the connection of one, two or four CAN networks to a PCI/104-Express-System. Up to three cards can be stacked...
View full details

from $355

Sale
Sale

$139

PCAN-MicroMod
PEAK-System Technik

Universal I/O Module with CAN Interface Please note: The product is expected to be available only until the end of 2024. If you need larger quantit...
View full details

$139

Sale
Sale

$379

PCAN-LIN Interface (high-speed/iso)
PEAK-System Technik

The PCAN-LIN module enables users to communicate over CAN, LIN and serial interface. The module is supplied in a plastic casing. The included firmw...
View full details

$379

Sale
Sale

$435

PCAN-Router FD w/ Phoenix connector
PEAK-System Technik

Universal Programmable Converter for CAN FD and CAN The PCAN-Router FD allows the connection to two CAN FD or CAN buses. Based on a ARM Cortex M4F ...
View full details

$435

Sale
Sale

$369

PCAN-Router w/ Phoenix connector
PEAK-System Technik

The PEAK PCAN-Router is a dual-channel CAN module with an NXP LPC21 series programmable microcontroller. This CAN router provides the option of u...
View full details

$369

Sale
Sale

$329

PCAN-Router DR
PEAK-System Technik

The PCAN-Router DR from PEAK features two high-speed CAN channels. The bit rate for each channel is adjusted with a rotary switch located on the fr...
View full details

$329

Sale
Sale

$479

PCAN-MicroMOD Evaluation Kit 2
PEAK-System Technik

Please note: The product is only available in smaller quantities. Unfortunately, larger quantities can no longer be produced. Please see the PCAN M...
View full details

$479

Sale
Sale

from $225

PCAN-PC/104 Adapter, iso (1ch/2ch)
PEAK-System Technik

This product is no longer available. The PCAN-PC/104 is a compact PC/104-CAN slot which allows the networking of two CAN buses to a PC/104 system. ...
View full details

from $225

Sale
Sale

$289

PCAN-MicroMod Digital 1
PEAK-System Technik

Please note: The product is only available in smaller quantities. Unfortunately, larger quantities can no longer be produced. Please see the PCAN M...
View full details

$289

Sale
Sale

$459

PCAN-WLAN Gateway DR
PEAK-System Technik

The PCAN-Wireless Gateway DR allows the connection of different CAN busses over IP networks. CAN frames are wrapped in TCP or UDP message packets a...
View full details

$459

Sale
Sale

$299

PCAN-ExpressCard 34
PEAK-System Technik

PEAK's CAN adapter PCAN-ExpressCard 34 allows the connection of a CAN bus to embedded PCs and laptops with ExpressCard slots. The card features gal...
View full details

$299

Sale
Sale

$499

PCAN-PC/104plus Quad Adapter, iso (4-channel)
PEAK-System Technik

The PCAN-PC/104-Plus Quad card enables the connection of four CAN networks to a PC/104-Plus system. Up to four cards can be stacked within one syst...
View full details

$499

Sale
Sale

$325

PCAN-LIN Interface (low-speed)
PEAK-System Technik

The PCAN-LIN module enables users to communicate over CAN, LIN and serial interface. The module is supplied in a plastic casing. The included firmw...
View full details

$325

Sale
Sale

$424

PCAN-MicroMod FD Analog 1
PEAK-System Technik

The PCAN-MicroMod FD plug-in board can be purchased together with ready-to-use motherboards that provide peripherals for specific requirements. Fo...
View full details

$424

Sale
Sale

$269

PCAN-MicroMod Mix 1 & 2
PEAK-System Technik

Application-specific PCAN-MicroMod Motherboards The motherboards for the PCAN-MicroMod provide an application-oriented environment. Typical charact...
View full details

$269

Sale