What is the warranty for Peak-System products?

Here is the complete hardware warranty section from the supplier. PCAN Adapter: PCAN-USB Adapter & PCAN-USB Adapter (Isolated)

I have a PCAN Adapter and have severed my cable to the service port on the engine. I am trying to confirm the wiring to the data link (from the CAN bus side).

These images show the pinout of the CAN bus side: Image 1 Image 2

Do you have a comparable product to Vector’s CANape and canoe/canalyzer?

You may want to look at the PCAN-USB Adapter with PCAN-Explorer 6 from PEAK. It will not be an exact 1:1 replacement, however.

Will the PCAN Adapter (2021, 2022, 4022, etc.) work with my [XYZ] device?

The PEAK PCAN-USB Adapter is a generic CAN interface for PC which allows CAN data exchange according to ISO 11898-2 with CAN bitrates of up to 1 Mbit/s. You will need to check if your devices also use a High-speed CAN connection per ISO 11898-2 standard. If they do, the chances are good that the PCAN-Adapter will work for you. We offer a 30-day money-back guarantee in the event it does not meet your needs.

What chips/circuitry are inside the PCAN USB Adapter?

The PCAN-USB Adapter has an FPGA with all the CAN controller circuitry, power supply circuits, and a CAN transceiver. For additional details, see the features section.

How does it handle 3.3 volt?

The PCAN-USB Adapter (IPEH-002021/22) will work with any CAN device that is ISO 11898-2 compliant. The adapter uses an NXP PCA82C251 CAN transceiver. Here is a link to the transceiver datasheet for full details on CAN voltages: PCA82C251 Datasheet

I ordered 3 PCAN USB adapters. If I want to connect two of them to talk to each other, and they are the only nodes on the CAN bus, what do I need to accomplish this?

You will need a terminated CAN cable such as our PCAN-Cable 2. Or something similar if you already have existing CAN cables. The DB-9 connector on the PCAN-USB Adapter is male. The cable has female connectors and the needed 120 Ohm termination resistors installed at both ends.

What chips/circuitry are inside the PCAN USB Adapter?

The PCAN-USB Adapter has an NXP CAN controller SJA1000 with 16 MHz clock frequency and an NXP CAN transceiver PCA82C251.

I am searching for a professional CAN Bus analyzer. We need the capability to monitor CAN Bus traffic and identify when message faults occur.

The PCAN-USB Adapter with PCAN-Explorer 6 software will serve your needs best!

I purchased the PCAN-USB Adapter (isolated). What else is required to record and then playback J1939 data?

The PCAN-Explorer V6 software with the J1939 add-in will work. We offer a 30-day trial with full functionality. Email us for your trial today.

I see the PCAN USB interface connects to a USB port, and the description says the interface is Linux compatible via SocketCAN. Does the driver present the socketCAN interface 'itself' (the USB interface being transparent), or will I have to provide the transport between the USB interface and the socketCAN interface?

The PEAK-System Linux page answers many of these questions and more. (SocketCAN is relevant for the SYSTEC USB-CANmodul from a different manufacturer.

I think the PCAN-USB Adapter (isolated) will work for the J1939 task I have. What do I need to be able to record and then playback that data?

The PCAN-Explorer V6 software with the J1939 add-in will work. PCAN-Explorer 6 Software

I purchased the PCAN-USB Adapter. Where can I download the driver for this USB adapter?

Windows and Linux drivers can be downloaded from the “Downloads” tab on the product page beneath the product description.

I have a IPEH-002262-KSM01. Do you have any example projects/files for this device? More than the examples provided in the manual?

The manufacturer has packaged all available files and demo projects into this download .

Is your CANopen Source Code UL (Underwriter Laboratories) certified?

No, our products are European, and CE certification is used for hardware, not software.

Can I download the software?

No, the process of getting the software ready and delivered via FTP transfer from SYSTEC usually takes one to two business days.

How do I set a custom CAN baud rate, for example, 333 kHz?

It is not possible to configure a CAN baud rate of exactly 333 kbit/s on the CAN-Ethernet Gateway V2. However, a baud rate of 333,333 kbit/s can be configured and has been tested. Please refer to the user's manual (section 6.4) for instructions on setting the gateway to this CAN baud rate.

Does the CANmodul1 require that a 120-ohm resistor be connected at the input port/CAN side?

Yes, a 120-ohm termination resistor is required at both ends of a CAN bus. If the CANmodul1 happens to be at the end, then an external bus termination is needed.

Will the CAN controller automatically determine whether it's a Standard or Extended ID?

Correct, no special settings are needed. The CAN controller automatically detects if it's 2.0A (11-bit identifier) or 2.0B (29-bit identifier) CAN specification.

What is the return policy?

Most unopened items in new condition and returned within 90 days will receive a refund or exchange. Some items have a modified return policy noted on the receipt or packing slip. Items that are opened or damaged or do not have a receipt may be denied a refund or exchange. Items purchased online or in-store may be returned to any store. Online purchases may be returned via a major parcel carrier. Click here to initiate a return.

How long does it take to process a refund?

We will reimburse you for returned items in the same way you paid for them. For example, any amounts deducted from a gift card will be credited back to a gift card. For returns by mail, once we receive your return, we will process it within 4–5 business days. It may take up to 7 days after we process the return to reflect in your account, depending on your financial institution's processing time.

What is the policy for late/non-delivery of items ordered online?

Our local teams work diligently to make sure that your order arrives on time, within our normaldelivery hours of 9AM to 8PM in the recipient's time zone. During busy holiday periods like Christmas, Valentine's and Mother's Day, we may extend our delivery hours before 9AM and after 8PM to ensure that all gifts are delivered on time. If for any reason your gift does not arrive on time, our dedicated Customer Service agents will do everything they can to help successfully resolve your issue. Click here to complete the form with your order-related question(s).

When will my credit card be charged?

We'll attempt to securely charge your credit card at the point of purchase online. If there's a problem, you'll be notified on the spot and prompted to use another card. Once we receive verification of sufficient funds, your payment will be completed and transferred securely to us. Your account will be charged in 24 to 48 hours.

Will I be charged sales tax for online orders?

Local and State sales tax will be collected if your recipient's mailing address is in: Arizona California Colorado

What software options do I need to purchase for the GEMAC CAN-Bus Tester 2?

There are 5 different add-on software licenses available. You will need one of the add-on licenses if you use a higher layer protocol such as CANopen, J1939, DeviceNet. There are also options for using a Protocol Monitor for one of these protocols. If you just use plain CAN, you may consider the Protocol Monitor CAN-License key for Protocol Monitor CAN (transmit / receive). The available licenses are as follows: CAN-Bus Tester 2: CANopen bus add-on $1039 CAN-Bus Tester 2: DeviceNet bus add-on $1239 CAN-Bus Tester 2: J1939 bus add-on $659 CAN-Bus Tester 2: Protocol Monitor CAN (Rx/Tx) $649 CAN-Bus Tester 2: Protocol Monitor CANopen (Receive) $519 CAN-Bus Tester 2: Protocol Monitor J1939 (Receive) $519

I'm looking at a GEMAC CAN-bus tester 2 for testing of CAN networks in our machines. Will I be able to debug the hardware side with the package by itself? What does the protocol monitor add-on do?

The protocol monitor does the following: CAN: Reception of CAN message frames incl. filtering, Transmission of CAN message frames and sequences (message lists) What level of testing do you plan to do? We're looking at debugging hardware issues with the network, would like to be able to determine problem messages/nodes on the network. I would recommend getting the protocol monitor license along with the CAN bus tester 2 device. Or you can buy the unit by itself first (available from stock) and see if you are okay without that license. You can always buy it at a later point.

What tools are available for developing a Windows-based CANopen application to talk to various CAN devices?

Phytools offers a number of different solutions for CANopen development on a Windows-based system. If you are looking for a full-featured CANopen source code package, we suggest the SYSTEC CANopen Source Code SO-877. This software is a full buyout license, meaning there will be no additional runtime fees or royalties for deployed products with this code inside. It can be used in combination with any SYSTEC CAN interface module. For developing PC-based applications in Windows, we recommend the CANopen Magic Pro DLL developed by our partner Embedded Systems Academy. This software works in combination with any PC-CAN interface made by PEAK-System Technik, such as their popular PCAN-USB Adapters. Embedded Systems Academy also has other CANopen network configuration tools that may be of interest. You can find more information on the Embedded Systems Academy page.

Are there any limitations to the CANopen Magic evaluation copy?

Yes, there are limitations to the CANopen Magic evaluation copy: 1. Communication with a real CAN bus is not possible. Instead, simulated CANopen nodes may be accessed over a purely internal CAN bus. 2. There is no command line interface to access the CAN bus. Please note: The features in this version match the full version of CANopen Magic Ultimate. There are other versions of CANopen Magic available with smaller feature sets. We hope you enjoy using this software and experimenting with CANopen!

Can I try this software before I purchase?

Yes, please email us for a 30-day PCAN Explorer Trial. You must also have a CAN interface, such as the PCAN USB Adapter. Each trial license includes all available add-in options.

I need a software program for collecting data off the J1939 Vehicle Network and parsing out each PGN and identifying which SPNs are available on the network and are changing in values to show it is valid data. What add-in or other product do I need to perform this?

You can do this with PCAN Explorer 6 with the J1939 add-in. We offer a 30-day trial of PCAN Explorer, and the trial comes with all the add-ins. Email us for your trial copy.

What is a .dbc file? (relevant for PCAN Explorer 6 - CANdb add-in)

A DBC file is a Communication Database for CAN. It is the distributed system's backbone. DBC files are basic text files that include information for decoding raw CAN bus data to physical values or in human-readable form. They specify which signals (e.g., RPM, Vehicle Speed, etc.) are contained within specific messages (i.e., CAN IDs). In developing a distributed ECU network based on CAN, a key component is the communication description in the form of DBC files. Described in DBC databases are the properties of the CAN network, the ECUs connected to the bus, and the CAN messages and signals.

My version of PCAN Trace (1.8.0.50) software is giving a bad file error message when trying to read my customers' 2.1 recordings. Can you help?

The PCAN-Trace can only handle trace files which comply with file version 1.x. A trace file that complies with version 2.x must be converted into file version 1.x with the 'PEAK-Converter.'

I am running PCAN Trace and collecting data off the J1939 Vehicle Network. I want to have a program that parses out each PGN and identifies which SPNs are available on the network and are changing in values to show it is valid data. What add-in or other product do I need to perform this?

PCAN Trace cannot do this, but you can do this with PCAN Explorer 6 with the J1939 add-in. We offer a 30-day trial of PCAN Explorer, and the trial comes with all the add-ins.

I am new to EtherCAT. I am looking for an EtherCAT Slave Unit that runs Linux on Raspberry Pi.

Yes, you can accomplish this with the Gateway Module Ethernet Slave coupled with the appropriate base RevPi module (IPC based on Raspberry Pi).

I need to convert two Modbus TCP devices to one Allen Bradley CompactLogix Ethernet IP. Questions I have are:

1. Hardware required. Looks like (1) KU-PR100066 and (1) KU-PR100088 would work? 2. Any additional hardware part number required to do this? 3. Can I convert both signals with one set of converters? A: The two gateway modules you inquired about (KU-PR100066 and KU-PR100088) will work to create a gateway system that connects Modbus TCP with Ethernet IP. The required connection clip is included. No additional items are needed.

Does the RevPi Core or Core 3 come with a power supply cable?

No, there is no cabling included with the RevPi Core or Core 3.

What are the mounting options for the RevPi Core or Core 3?

The RevPi Core or Core 3 can be mounted on a DIN rail housing (for DIN rail version EN 50022).

Does the RevPi Core or Core 3 come with an SD card?

No, there is no SD card included with the RevPi Core or Core 3. You can use a USB memory stick for data storage.

What are the graphics specs of the RevPi Core or Core 3? I need to drive a large LCD display.

The RevPi Core is based on the Broadcom BCM2711, quad-core Arm Cortex-A72. For more information, visit click here The RevPi Core 3 is based on the Broadcom BCM2837 processor. For more information, click here For more information on the VideoCore subsystem, see click here .

What are the limitations of the CANopen Magic evaluation?

The CANopen Magic evaluation has limitations. Please refer to the documentation and licensing information provided by Embedded Systems Academy, Inc.

What is the HS code for the following items: PCAN Cable 1 w/o termination, PCAN T-Adapter, PCAN-USB Adapter

The HTS code for cables and T-adapters is 8544429000. The PCAN-USB adapter is 8517620050. The ECCN number for all products is EAR99. All are manufactured in Germany.

How do I calculate the baud rate?

There is a tool made by PEAK for calculating the baud rate register settings: baudtool.zip

Are the SYS TEC Canmodul1 and the Kvaser Leaf Light v2 the same product essentially?

The two devices provide similar functionality in that they both connect a PC or laptop via its USB interface to a CAN bus. Both devices support the maximum CAN bitrate of 1 Mbit/s. However, both devices have unique designs in terms of internal circuitry and software API/drivers. There are other differences in terms of CAN message throughput, buffer size, etc. If you are using third-party software that specifically requires the use of the Kvaser Leaf Light V2, then I strongly advise against using a different type of USB-CAN interface.

I'm currently using the PCAN-USB to view 500k CAN bus data on cars. I would like to be able to view the LIN bus data on Chrysler vehicles 2011 and newer. Do I need a dedicated LIN interface or is there one that will do both LIN and CAN?

Phytools offers a PLIN-USB Adapter (dedicated LIN interface) and several interfaces that support both CAN and LIN, including the PCAN USB Pro FD, the Kvaser Hybrid, and the CAN FD LIN Gateway.

I am looking for an isolated CAN repeater, and I saw the one you have rated to 500V. Do you have any rated for higher voltages, around 1.5-2 kV?

The PCAN-Repeater DR establishes a galvanic isolation of up to 5 kV according to IEC60601-1 within a High-speed CAN bus. Both CAN ports are decoupled from each other and from the power supply. All message traffic, including error frames, is forwarded 1:1 between both ports. The PCAN-Repeater DR behaves passively and is transparent from the perspective of the CAN bus. LEDs display the current bus status.

I'm currently using the PCAN-USB Adapter to view 500k CAN bus data on cars. I would like to be able to view the LIN bus data on Chrysler vehicles 2011 and newer. Do I need a dedicated LIN interface or is there one that will do both LIN and CAN?

Phytools offers a PLIN-USB Adapter (dedicated LIN interface) and several interfaces that support both CAN and LIN, including the PCAN USB Pro FD, the Kvaser Hybrid, and the CAN FD LIN Gateway.

I am looking for the ability to connect two CAN FD channels and have the ability to process, manipulate, and filter CAN messages bidirectionally between each bus. Which products do I need?

There are two solutions: PC-based solution or a standalone solution. For the former, you can use PCAN-USB Pro FD Adapter, which has two independent CAN FD capable channels. Any message processing, manipulating, filtering, etc. will require using the corresponding PC software based on the PCAN Basic API. For the latter, use the PCAN Router FD with specially programmed firmware as a stand-alone CAN FD router.

I just need a simple CAN interface with some software that can receive and display CAN messages from other nodes as well as send CAN messages out to other nodes. What device would you recommend?

We suggest a PCAN-USB Interface with the included free PCAN-View software. If you need a device that is able to detect and analyze more of the physical layer properties of a CAN system, we do offer CAN diagnostic tools as well.

Products

Sort by

Show
24
36
48

View as

Sale

from $62

PCAN SAE J1939 Cable
PEAK-System Technik

High-Speed CAN cable for J1939 Connectors Establish standardized, reliable communication between components with the SAE J1939 connector from PEAK-...
View full details

from $62

Sale
Sale

from $23

PCAN T-Adapter
PEAK-System Technik

Create a tap connection to the data cables and the ground. With a CAN bus in order to be able to connect a further CAN node. In this case, the CAN ...
View full details

from $23

Sale
Sale

$22

PCAN Termination Adapter
PEAK-System Technik

Adapter For High-speed CAN buses. CAN Termination Adapter(ISO 11898-2) must be terminated at their ends by resistors.The adapters PCAN-Term and PCA...
View full details

$22

Sale
Sale

$239

PCAN USB Adapter
PEAK-System Technik

Connect any laptop, computer or PC to a CANbus via USB. This CAN-USB interface, with the included CAN monitor software, allows a user to look at CA...
View full details

$239

Sale
Sale

$296

PCAN USB Adapter (isolated)
PEAK-System Technik

Makes it possible to connect any PC with a USB slot into a CAN network. Galvanic isolation of up to 500V between the CAN signals and the host-PC i...
View full details

$296

Sale
Sale

$8

PCAN-Adapter D-Sub to Screw Terminals
PEAK-System Technik

Allows easy connection of open cable ends of a CAN bus to a D-Sub connector The adapter with a D-Sub socket connector and a three-pin screw termina...
View full details

$8

Sale
Sale

$173

PCAN-AU5790
PEAK-System Technik

Establishes a connection between a High-speed CAN bus (ISO 11898-2) and a Single-wire CAN bus (SAE J2411) One of the most important potential appli...
View full details

$173

Sale
Sale

$0

PCAN-Basic
PEAK-System Technik

Allows easy development of powerful software with CAN and CAN FD support. It includes all of the functions that an application needs in order to c...
View full details

$0

Sale
Sale

$35

PCAN-Cable 3
PEAK-System Technik

CAN Cable for Test and Measurement Setups With this cable the two components CAN-High and CAN-Low of the differential CAN signal can be picked up f...
View full details

$35

Sale
Sale

$35

PCAN-Cable M12
PEAK-System Technik

CAN Adapter Cable from D-Sub Socket to M12 Circular Connector M12 circular connectors are robust and offer increased protection against environment...
View full details

$35

Sale
Sale

$0

PCAN-CCP API
PEAK-System Technik

A programming interface for the communication between Windows® applications (Masters) and electronic control units (Slave ECUs). The API is based ...
View full details

$0

Sale
Sale

$299

PCAN-Chip USB-Eval
PEAK-System Technik

Stamp Module utilized for the Implementation of CAN FD to USB Connections. (The chip itself is not available for online ordering. NDA documents mus...
View full details

$299

Sale
Sale

$17

PCAN-D-Sub Connection Adapter
PEAK-System Technik

Hardware product in DIN rail housing features a 4-pin screw terminal block as CAN connector. The PCAN-D-Sub Connection Adapter routes the CAN sign...
View full details

$17

Sale
Sale

$1,999

PCAN-Developer 4
PEAK-System Technik

Professional CAN and CAN FD Development Software Package for Windows® PEAK's new PCAN-Developer 4 Software Package is a flexible system for plannin...
View full details

$1,999

Sale
Sale

$1,180

PCAN-Diag 2
PEAK-System Technik

END OF LIFE - This product will be discontinued. (call for details) The PCAN-Diag 2 designed by PEAK-System Technik is a handheld diagnostics unit...
View full details

$1,180

Sale
Sold out

from $1,778

PCAN-Diag FD
PEAK-System Technik

A mobile device for the diagnosis of CAN FD bus communications. (sold out until November) Analysis can be done at the protocol layer by handling ...
View full details

from $1,778

Sold out
Sale

from $199

PCAN-Diag FD J1939 Add-in
PEAK-System Technik

Describes communication in utility vehicles via CAN Using PGs (Parameter Groups) and SPs (Suspect Parameters), the standard defines messages and da...
View full details

from $199

Sale
Sale

$354

PCAN-Ethernet Gateway DR
PEAK-System Technik

Provides one LAN connection and two High-speed CAN interfaces. The PCAN-Ethernet Gateway DR allows the connection of different CAN busses over IP n...
View full details

$354

Sale
Sale

$804

PCAN-Ethernet Gateway FD DR
PEAK-System Technik

CAN FD to LAN Gateway in DIN Rail Plastic Casing The PCAN-Ethernet Gateway FD DR allows access to classic CAN or modern CAN FD buses via an IP netw...
View full details

$804

Sale
Sale

$832

PCAN-Explorer 6 (Portable License)
PEAK-System Technik

The PCAN-Explorer 6 portable license enables seamless use of the Windows software across multiple computers without the need for separate installat...
View full details

$832

Sale
Sale

$699

PCAN-Explorer 6 Software
PEAK-System Technik

CAN Network Monitoring SoftwareSingle Computer License (Portable license also available) The new PCAN-Explorer 6 developed by PEAK-System Technik...
View full details

$699

Sale
Sale

from $199

PCAN-ExpressCard (1ch/2ch)
PEAK-System Technik

EOL NOTIFICATION: Product is at its end of life and will no longer be available once stock is depleted. THIS PRODUCT IS OBSOLETE The PCAN-Expr...
View full details

from $199

Sale
Sale

$299

PCAN-ExpressCard 34
PEAK-System Technik

EOL NOTIFICATION: Product is at its end of life and will no longer be available once stock is depleted. Allows the connection of a CAN bus to em...
View full details

$299

Sale
Sale

$799

PCAN-FMS Simulator 2
PEAK-System Technik

Windows® Software for Simulating CAN Data According to FMS Standard The FMS (Fleet Management System) and Bus-FMS protocols provide a manufacturer-...
View full details

$799

Sale
Sold out

$499

PCAN-GPRS-Link
PEAK-System Technik

NOTE: This product has been discontinued by the manufacturer. Customers are encouraged to consider the recommended replacement product, PCAN-GPS...
View full details

$499

Sold out
Sale

$629

PCAN-GPRS-Link Evaluation Kit
PEAK-System Technik

Discontinued Product For a replacement the PCAN-GPS SKU #: IPEH-002110 is recommended. A module for recording and forwarding vehicle data. The...
View full details

$629

Sale
Sale

$378

PCAN-GPS
PEAK-System Technik

END OF LIFE - This product has been Discontinued (limited to stock on hand) Call for details. The PCAN-GPS made by PEAK-System Technik (Germany) i...
View full details

$378

Sale
Sale

$409

PCAN-GPS FD
PEAK-System Technik

Programmable Sensor Module with CAN FD Connection The PCAN-GPS FD is a programmable sensor module for position and orientation determination with...
View full details

$409

Sale
Sale

$899

PCAN-GPS Pro FD
PEAK-System Technik

A configurable sensor module for determining position and acceleration. The PCAN-GPS Pro FD is a configurable sensor module for detecting position,...
View full details

$899

Sale
Sale

$0

PCAN-ISO-TP API
PEAK-System Technik

An international standard for the transfer of data packages via CAN. Above CAN (OSI layers 1 and 2). The protocol covers the OSI layers 3 (Network...
View full details

$0

Sale
Sale

$336

PCAN-LIN Interface (high-speed CAN)
PEAK-System Technik

The PCAN-LIN module enables users to communicate over CAN, LIN and serial interface. The module is supplied in a plastic casing. The included firmw...
View full details

$336

Sale
Sale

$400

PCAN-LIN Interface (high-speed/iso)
PEAK-System Technik

This module enables users to communicate over CAN, LIN and serial interface. The module is supplied in a plastic casing. The included firmware enab...
View full details

$400

Sale
Sale

$325

PCAN-LIN Interface (low-speed)
PEAK-System Technik

This module (low speed) enables users to communicate over CAN, LIN and serial interface. The included firmware enables data exchange between the di...
View full details

$325

Sale
Sale

from $1,224

PCAN-LWL
PEAK-System Technik

Coupling for optical transmission of CAN and CAN FD data. For use in explosion-proof areas or for EMI/EMC measurements, the PCAN-LWL can be used to...
View full details

from $1,224

Sale
Sale

from $331

PCAN-M.2
PEAK-System Technik

Connects CAN and CAN FD networks to a computer board via its M.2 interface (PCIe). With its small form factor, the plug-in card is optimal for emb...
View full details

from $331

Sale
Sold out

$154

PCAN-MicroMod
PEAK-System Technik

This product is EOL. Product is no longer available. Please consider this newer version instead. Contact Sales@phytools.com for further assistance ...
View full details

$154

Sold out
Sale

$317

PCAN-MicroMod Analog 1
PEAK-System Technik

The motherboards provide an application-oriented environment. Please note: The product is only available in smaller quantities. Unfortunately, larg...
View full details

$317

Sale
Sale

$440

PCAN-MicroMod Analog 2
PEAK-System Technik

Please note: The product is only available in smaller quantities. Unfortunately, larger quantities can no longer be produced. Please see the PCAN M...
View full details

$440

Sale
Sale

$317

PCAN-MicroMod Digital 1
PEAK-System Technik

Implementation-ready CAN or CANopen I/O systems suitable for a wide range of industrial control applications. Please note: The product is only avai...
View full details

$317

Sale
Sale

$317

PCAN-MicroMod Digital 2
PEAK-System Technik

Implementation-ready CAN or CANopen I/O systems suitable for a wide range of industrial control applications. Please note: The product is only avai...
View full details

$317

Sale
Sold out

$531

PCAN-MicroMod Evaluation Kit
PEAK-System Technik

Please note: The product has been discontinued. Please see the PCAN MicroMod FD series for new projects. This MicroMod Evaluation Kit from PEAK pr...
View full details

$531

Sold out
Sale

$143

PCAN-MicroMod FD
PEAK-System Technik

Universal I/O Module with CAN FD Interface (This is the suggested replacement for PCAN-Micro Mod SKU#: IPEH-002080) The PCAN-MicroMod FD is a small...
View full details

$143

Sale
Sale

$488

PCAN-MicroMod FD Analog 1
PEAK-System Technik

For the connection of CAN, I/O, and power supply, spring terminal connectors. The PCAN-MicroMod FD plug-in board can be purchased together with...
View full details

$488

Sale
Sale

$397

PCAN-MicroMod FD Digital 1
PEAK-System Technik

Purchased together with ready-to-use motherboards that provide peripherals for specific requirements. The PCAN-MicroMod FD plug-in board for the co...
View full details

$397

Sale
Sale

$397

PCAN-MicroMod FD Digital 2
PEAK-System Technik

Purchased together with ready-to-use motherboards that provide peripherals for specific requirements. For the connection of CAN, I/O, and power su...
View full details

$397

Sale
Sale

$473

PCAN-MicroMod FD DR CANopen Digital 1
PEAK-System Technik

Industrial CANopen and CANopen FD Module for Digital I/O Applications The PCAN-MicroMod FD DR CANopen Digital 1 is an I/O module for operation in C...
View full details

$473

Sale
Sale

$799

PCAN-MicroMod FD ECU
PEAK-System Technik

Universal, Configurable Control Unit with I/O and CAN FD Connection The PCAN-MicroMod FD ECU serves as a versatile control module, engineered for...
View full details

$799

Sale
Sale

$659

PCAN-MicroMod FD ECU Adapter
PEAK-System Technik

Simple connection for the PCAN-MicroMod FD ECU. The PCAN-MicroMod FD ECU Adapter allows simplified wiring of the PCAN-MicroMod FD ECU using Phoenix...
View full details

$659

Sale