What is the warranty for Peak-System products?

Here is the complete hardware warranty section from the supplier. PCAN Adapter: PCAN-USB Adapter & PCAN-USB Adapter (Isolated)

I have a PCAN Adapter and have severed my cable to the service port on the engine. I am trying to confirm the wiring to the data link (from the CAN bus side).

These images show the pinout of the CAN bus side: Image 1 Image 2

Do you have a comparable product to Vector’s CANape and canoe/canalyzer?

You may want to look at the PCAN-USB Adapter with PCAN-Explorer 6 from PEAK. It will not be an exact 1:1 replacement, however.

Will the PCAN Adapter (2021, 2022, 4022, etc.) work with my [XYZ] device?

The PEAK PCAN-USB Adapter is a generic CAN interface for PC which allows CAN data exchange according to ISO 11898-2 with CAN bitrates of up to 1 Mbit/s. You will need to check if your devices also use a High-speed CAN connection per ISO 11898-2 standard. If they do, the chances are good that the PCAN-Adapter will work for you. We offer a 30-day money-back guarantee in the event it does not meet your needs.

What chips/circuitry are inside the PCAN USB Adapter?

The PCAN-USB Adapter has an FPGA with all the CAN controller circuitry, power supply circuits, and a CAN transceiver. For additional details, see the features section.

How does it handle 3.3 volt?

The PCAN-USB Adapter (IPEH-002021/22) will work with any CAN device that is ISO 11898-2 compliant. The adapter uses an NXP PCA82C251 CAN transceiver. Here is a link to the transceiver datasheet for full details on CAN voltages: PCA82C251 Datasheet

I ordered 3 PCAN USB adapters. If I want to connect two of them to talk to each other, and they are the only nodes on the CAN bus, what do I need to accomplish this?

You will need a terminated CAN cable such as our PCAN-Cable 2. Or something similar if you already have existing CAN cables. The DB-9 connector on the PCAN-USB Adapter is male. The cable has female connectors and the needed 120 Ohm termination resistors installed at both ends.

What chips/circuitry are inside the PCAN USB Adapter?

The PCAN-USB Adapter has an NXP CAN controller SJA1000 with 16 MHz clock frequency and an NXP CAN transceiver PCA82C251.

I am searching for a professional CAN Bus analyzer. We need the capability to monitor CAN Bus traffic and identify when message faults occur.

The PCAN-USB Adapter with PCAN-Explorer 6 software will serve your needs best!

I purchased the PCAN-USB Adapter (isolated). What else is required to record and then playback J1939 data?

The PCAN-Explorer V6 software with the J1939 add-in will work. We offer a 30-day trial with full functionality. Email us for your trial today.

I see the PCAN USB interface connects to a USB port, and the description says the interface is Linux compatible via SocketCAN. Does the driver present the socketCAN interface 'itself' (the USB interface being transparent), or will I have to provide the transport between the USB interface and the socketCAN interface?

The PEAK-System Linux page answers many of these questions and more. (SocketCAN is relevant for the SYSTEC USB-CANmodul from a different manufacturer.

I think the PCAN-USB Adapter (isolated) will work for the J1939 task I have. What do I need to be able to record and then playback that data?

The PCAN-Explorer V6 software with the J1939 add-in will work. PCAN-Explorer 6 Software

I purchased the PCAN-USB Adapter. Where can I download the driver for this USB adapter?

Windows and Linux drivers can be downloaded from the “Downloads” tab on the product page beneath the product description.

I have a IPEH-002262-KSM01. Do you have any example projects/files for this device? More than the examples provided in the manual?

The manufacturer has packaged all available files and demo projects into this download .

Is your CANopen Source Code UL (Underwriter Laboratories) certified?

No, our products are European, and CE certification is used for hardware, not software.

Can I download the software?

No, the process of getting the software ready and delivered via FTP transfer from SYSTEC usually takes one to two business days.

How do I set a custom CAN baud rate, for example, 333 kHz?

It is not possible to configure a CAN baud rate of exactly 333 kbit/s on the CAN-Ethernet Gateway V2. However, a baud rate of 333,333 kbit/s can be configured and has been tested. Please refer to the user's manual (section 6.4) for instructions on setting the gateway to this CAN baud rate.

Does the CANmodul1 require that a 120-ohm resistor be connected at the input port/CAN side?

Yes, a 120-ohm termination resistor is required at both ends of a CAN bus. If the CANmodul1 happens to be at the end, then an external bus termination is needed.

Will the CAN controller automatically determine whether it's a Standard or Extended ID?

Correct, no special settings are needed. The CAN controller automatically detects if it's 2.0A (11-bit identifier) or 2.0B (29-bit identifier) CAN specification.

What is the return policy?

Most unopened items in new condition and returned within 90 days will receive a refund or exchange. Some items have a modified return policy noted on the receipt or packing slip. Items that are opened or damaged or do not have a receipt may be denied a refund or exchange. Items purchased online or in-store may be returned to any store. Online purchases may be returned via a major parcel carrier. Click here to initiate a return.

How long does it take to process a refund?

We will reimburse you for returned items in the same way you paid for them. For example, any amounts deducted from a gift card will be credited back to a gift card. For returns by mail, once we receive your return, we will process it within 4–5 business days. It may take up to 7 days after we process the return to reflect in your account, depending on your financial institution's processing time.

What is the policy for late/non-delivery of items ordered online?

Our local teams work diligently to make sure that your order arrives on time, within our normaldelivery hours of 9AM to 8PM in the recipient's time zone. During busy holiday periods like Christmas, Valentine's and Mother's Day, we may extend our delivery hours before 9AM and after 8PM to ensure that all gifts are delivered on time. If for any reason your gift does not arrive on time, our dedicated Customer Service agents will do everything they can to help successfully resolve your issue. Click here to complete the form with your order-related question(s).

When will my credit card be charged?

We'll attempt to securely charge your credit card at the point of purchase online. If there's a problem, you'll be notified on the spot and prompted to use another card. Once we receive verification of sufficient funds, your payment will be completed and transferred securely to us. Your account will be charged in 24 to 48 hours.

Will I be charged sales tax for online orders?

Local and State sales tax will be collected if your recipient's mailing address is in: Arizona California Colorado

What software options do I need to purchase for the GEMAC CAN-Bus Tester 2?

There are 5 different add-on software licenses available. You will need one of the add-on licenses if you use a higher layer protocol such as CANopen, J1939, DeviceNet. There are also options for using a Protocol Monitor for one of these protocols. If you just use plain CAN, you may consider the Protocol Monitor CAN-License key for Protocol Monitor CAN (transmit / receive). The available licenses are as follows: CAN-Bus Tester 2: CANopen bus add-on $1039 CAN-Bus Tester 2: DeviceNet bus add-on $1239 CAN-Bus Tester 2: J1939 bus add-on $659 CAN-Bus Tester 2: Protocol Monitor CAN (Rx/Tx) $649 CAN-Bus Tester 2: Protocol Monitor CANopen (Receive) $519 CAN-Bus Tester 2: Protocol Monitor J1939 (Receive) $519

I'm looking at a GEMAC CAN-bus tester 2 for testing of CAN networks in our machines. Will I be able to debug the hardware side with the package by itself? What does the protocol monitor add-on do?

The protocol monitor does the following: CAN: Reception of CAN message frames incl. filtering, Transmission of CAN message frames and sequences (message lists) What level of testing do you plan to do? We're looking at debugging hardware issues with the network, would like to be able to determine problem messages/nodes on the network. I would recommend getting the protocol monitor license along with the CAN bus tester 2 device. Or you can buy the unit by itself first (available from stock) and see if you are okay without that license. You can always buy it at a later point.

What tools are available for developing a Windows-based CANopen application to talk to various CAN devices?

Phytools offers a number of different solutions for CANopen development on a Windows-based system. If you are looking for a full-featured CANopen source code package, we suggest the SYSTEC CANopen Source Code SO-877. This software is a full buyout license, meaning there will be no additional runtime fees or royalties for deployed products with this code inside. It can be used in combination with any SYSTEC CAN interface module. For developing PC-based applications in Windows, we recommend the CANopen Magic Pro DLL developed by our partner Embedded Systems Academy. This software works in combination with any PC-CAN interface made by PEAK-System Technik, such as their popular PCAN-USB Adapters. Embedded Systems Academy also has other CANopen network configuration tools that may be of interest. You can find more information on the Embedded Systems Academy page.

Are there any limitations to the CANopen Magic evaluation copy?

Yes, there are limitations to the CANopen Magic evaluation copy: 1. Communication with a real CAN bus is not possible. Instead, simulated CANopen nodes may be accessed over a purely internal CAN bus. 2. There is no command line interface to access the CAN bus. Please note: The features in this version match the full version of CANopen Magic Ultimate. There are other versions of CANopen Magic available with smaller feature sets. We hope you enjoy using this software and experimenting with CANopen!

Can I try this software before I purchase?

Yes, please email us for a 30-day PCAN Explorer Trial. You must also have a CAN interface, such as the PCAN USB Adapter. Each trial license includes all available add-in options.

I need a software program for collecting data off the J1939 Vehicle Network and parsing out each PGN and identifying which SPNs are available on the network and are changing in values to show it is valid data. What add-in or other product do I need to perform this?

You can do this with PCAN Explorer 6 with the J1939 add-in. We offer a 30-day trial of PCAN Explorer, and the trial comes with all the add-ins. Email us for your trial copy.

What is a .dbc file? (relevant for PCAN Explorer 6 - CANdb add-in)

A DBC file is a Communication Database for CAN. It is the distributed system's backbone. DBC files are basic text files that include information for decoding raw CAN bus data to physical values or in human-readable form. They specify which signals (e.g., RPM, Vehicle Speed, etc.) are contained within specific messages (i.e., CAN IDs). In developing a distributed ECU network based on CAN, a key component is the communication description in the form of DBC files. Described in DBC databases are the properties of the CAN network, the ECUs connected to the bus, and the CAN messages and signals.

My version of PCAN Trace (1.8.0.50) software is giving a bad file error message when trying to read my customers' 2.1 recordings. Can you help?

The PCAN-Trace can only handle trace files which comply with file version 1.x. A trace file that complies with version 2.x must be converted into file version 1.x with the 'PEAK-Converter.'

I am running PCAN Trace and collecting data off the J1939 Vehicle Network. I want to have a program that parses out each PGN and identifies which SPNs are available on the network and are changing in values to show it is valid data. What add-in or other product do I need to perform this?

PCAN Trace cannot do this, but you can do this with PCAN Explorer 6 with the J1939 add-in. We offer a 30-day trial of PCAN Explorer, and the trial comes with all the add-ins.

I am new to EtherCAT. I am looking for an EtherCAT Slave Unit that runs Linux on Raspberry Pi.

Yes, you can accomplish this with the Gateway Module Ethernet Slave coupled with the appropriate base RevPi module (IPC based on Raspberry Pi).

I need to convert two Modbus TCP devices to one Allen Bradley CompactLogix Ethernet IP. Questions I have are:

1. Hardware required. Looks like (1) KU-PR100066 and (1) KU-PR100088 would work? 2. Any additional hardware part number required to do this? 3. Can I convert both signals with one set of converters? A: The two gateway modules you inquired about (KU-PR100066 and KU-PR100088) will work to create a gateway system that connects Modbus TCP with Ethernet IP. The required connection clip is included. No additional items are needed.

Does the RevPi Core or Core 3 come with a power supply cable?

No, there is no cabling included with the RevPi Core or Core 3.

What are the mounting options for the RevPi Core or Core 3?

The RevPi Core or Core 3 can be mounted on a DIN rail housing (for DIN rail version EN 50022).

Does the RevPi Core or Core 3 come with an SD card?

No, there is no SD card included with the RevPi Core or Core 3. You can use a USB memory stick for data storage.

What are the graphics specs of the RevPi Core or Core 3? I need to drive a large LCD display.

The RevPi Core is based on the Broadcom BCM2711, quad-core Arm Cortex-A72. For more information, visit click here The RevPi Core 3 is based on the Broadcom BCM2837 processor. For more information, click here For more information on the VideoCore subsystem, see click here .

What are the limitations of the CANopen Magic evaluation?

The CANopen Magic evaluation has limitations. Please refer to the documentation and licensing information provided by Embedded Systems Academy, Inc.

What is the HS code for the following items: PCAN Cable 1 w/o termination, PCAN T-Adapter, PCAN-USB Adapter

The HTS code for cables and T-adapters is 8544429000. The PCAN-USB adapter is 8517620050. The ECCN number for all products is EAR99. All are manufactured in Germany.

How do I calculate the baud rate?

There is a tool made by PEAK for calculating the baud rate register settings: baudtool.zip

Are the SYS TEC Canmodul1 and the Kvaser Leaf Light v2 the same product essentially?

The two devices provide similar functionality in that they both connect a PC or laptop via its USB interface to a CAN bus. Both devices support the maximum CAN bitrate of 1 Mbit/s. However, both devices have unique designs in terms of internal circuitry and software API/drivers. There are other differences in terms of CAN message throughput, buffer size, etc. If you are using third-party software that specifically requires the use of the Kvaser Leaf Light V2, then I strongly advise against using a different type of USB-CAN interface.

I'm currently using the PCAN-USB to view 500k CAN bus data on cars. I would like to be able to view the LIN bus data on Chrysler vehicles 2011 and newer. Do I need a dedicated LIN interface or is there one that will do both LIN and CAN?

Phytools offers a PLIN-USB Adapter (dedicated LIN interface) and several interfaces that support both CAN and LIN, including the PCAN USB Pro FD, the Kvaser Hybrid, and the CAN FD LIN Gateway.

I am looking for an isolated CAN repeater, and I saw the one you have rated to 500V. Do you have any rated for higher voltages, around 1.5-2 kV?

The PCAN-Repeater DR establishes a galvanic isolation of up to 5 kV according to IEC60601-1 within a High-speed CAN bus. Both CAN ports are decoupled from each other and from the power supply. All message traffic, including error frames, is forwarded 1:1 between both ports. The PCAN-Repeater DR behaves passively and is transparent from the perspective of the CAN bus. LEDs display the current bus status.

I'm currently using the PCAN-USB Adapter to view 500k CAN bus data on cars. I would like to be able to view the LIN bus data on Chrysler vehicles 2011 and newer. Do I need a dedicated LIN interface or is there one that will do both LIN and CAN?

Phytools offers a PLIN-USB Adapter (dedicated LIN interface) and several interfaces that support both CAN and LIN, including the PCAN USB Pro FD, the Kvaser Hybrid, and the CAN FD LIN Gateway.

I am looking for the ability to connect two CAN FD channels and have the ability to process, manipulate, and filter CAN messages bidirectionally between each bus. Which products do I need?

There are two solutions: PC-based solution or a standalone solution. For the former, you can use PCAN-USB Pro FD Adapter, which has two independent CAN FD capable channels. Any message processing, manipulating, filtering, etc. will require using the corresponding PC software based on the PCAN Basic API. For the latter, use the PCAN Router FD with specially programmed firmware as a stand-alone CAN FD router.

I just need a simple CAN interface with some software that can receive and display CAN messages from other nodes as well as send CAN messages out to other nodes. What device would you recommend?

We suggest a PCAN-USB Interface with the included free PCAN-View software. If you need a device that is able to detect and analyze more of the physical layer properties of a CAN system, we do offer CAN diagnostic tools as well.

CAN Software

We offer the widest selection of sophisticated CAN software products for a variety of application needs. With our off-shelve CAN analyzing software customers will be able to test new CAN products as well as existing systems with minimal effort and within a very short amount of time. Our products allow you to record large CAN data streams, export or import messages, convert CAN frames into graphical display elements and much more. Higher-layer protocol support is also available with a focus on CANopen and J1939. Phytools provides instant free technical support and same day order processing to get your CAN project started in no time. Talk to our CAN expert to find the product that is right for you or discuss product customization for OEM integration into your own system.

Sort by

Show
24
36
48

View as

Sale

$832

PCAN-Explorer 6 Portable License
PEAK-System Technik

CAN/CANFD Network Monitoring SoftwarePortable License with Copy Protection Dongle (Request free 30 day trial) PCAN-Explorer 6 Windows software is...
View full details

$832

Sale
Sale

$126

PCAN Explorer 6 - CANdb add-in
PEAK-System Technik

Optional Function Upgrades for PCAN-Explorer V6 Note: Please provide your PCAN Explorer 6 original License Id in the notes section of the checkou...
View full details

$126

Sale
Sale

$699

PCAN-Explorer 6 Software
PEAK-System Technik

CAN Network Monitoring SoftwareSingle Computer License (Portable license also available) The new PCAN-Explorer 6 developed by PEAK-System Technik...
View full details

$699

Sale
Sale

$213

PCAN-Panel plug-in for PCAN Explorer 6
PEAK-System Technik

Optional Function Upgrades for PCAN-Explorer V6 Note: Please provide your PCAN Explorer 6 original License Id in the notes section of the checkout ...
View full details

$213

Sale
Sale

$213

PCAN-Plotter plug-in for PCAN Explorer 6
PEAK-System Technik

Optional Function Upgrades for PCAN-Explorer V6 Note: Please provide your PCAN Explorer 6 original License Id in the notes section of the checkout ...
View full details

$213

Sale
Sale

$416

PCAN Explorer 6 - J1939 add-in
PEAK-System Technik

Communication on a CAN bus in utility vehicles for the transmission of diagnostics data and control information is describes in the SAE J1939 netwo...
View full details

$416

Sale
Sale

$89

LabView Driver for PCAN-Basic 4.x
KDI Digital Instrumentation

LabVIEW® API for PCAN© BASIC FD 4.0 The LabVIEW® API uses the PCAN© Basic 4.0 API from PEAK-System. It allows you to exchange CAN messages via CAN ...
View full details

$89

Sale
Sale

$0

PCAN-View (Free CAN/CAN FD Monitor)
PEAK-System Technik

Windows® Software for Displaying CAN and CAN FD Messages PCAN-View is a straightforward CAN monitor software for Windows. It enables users to view...
View full details

$0

Sale
Sale

$379

PCAN-Trace Data Logger
PEAK-System Technik

Comprehensive CAN Data Logger from PEAK The PEAK PCAN-Trace program is a data logger which is capable to record up to 9,999,000 CAN messages. All m...
View full details

$379

Sale
Sale

$0

PCAN-Basic
PEAK-System Technik

The PCAN-Basic API (application programming interface) allows easy development of powerful software with CAN and CAN FD support. It includes all of...
View full details

$0

Sale
Sale

$0

PCAN-RP1210 API
PEAK-System Technik

The Recommended Practice 1210 was defined by the Technology and Maintenance Council (TMC) as a standardized API for communication between Windows® ...
View full details

$0

Sale
Sale

$0

PLIN-API
PEAK-System Technik

LIN (Local Interconnect Network) is a serial network protocol which is characterized by a master-slave architecture and transmission patterns. The ...
View full details

$0

Sale
Sale

$0

PCAN-PassThru API
PEAK-System Technik

For the programming of control units (ECU), there are countless applications from various manufacturers which are used in the development and diagn...
View full details

$0

Sale
Sale

$0

PCAN-OBD-2 API
PEAK-System Technik

For on-board diagnostics, the OBD-2 standard defines the exchange of specific vehicle parameters. The client makes a request on the connected contr...
View full details

$0

Sale
Sale

$1,169

CANopen Magic Professional
Embedded Systems Academy

Professional CANopen configuration and analysis tool. High accuracy timestamps, Electronic Datasheet support, network configuration and easy PDO co...
View full details

$1,169

Sale
Sale

$0

PCAN-CCP API
PEAK-System Technik

The PCAN-CCP API is a programming interface for the communication between Windows® applications (Masters) and electronic control units (Slave ECUs)...
View full details

$0

Sale
Sale

$1,999

PCAN-Developer 4
PEAK-System Technik

Professional CAN and CAN FD Development Package for Windows® PEAK's new PCAN-Developer 4 Software Package is a flexible system for planning, devel...
View full details

$1,999

Sale
Sold out

$0

PCAN-UDS API
PEAK-System Technik

UDS (ISO 14229-1) stands for Unified Diagnostic Services and defines the communication with control units (ECUs). The Windows® software tests the c...
View full details

$0

Sold out
Sale

$119

LabView Driver for PCAN-Developer
KDI Digital Instrumentation

LabVIEW® API for PCAN© Developer 4.x driver This API uses the PCAN©-Developer 4.x API from PEAK-System to establish one or more CAN networks. Usin...
View full details

$119

Sale
Sale

$0

PCAN-ISO-TP API
PEAK-System Technik

ISO-TP (ISO 15765-2) is an international standard for the transfer of data packages via CAN. Above CAN (OSI layers 1 and 2), the protocol covers th...
View full details

$0

Sale
Sale

$0

PCAN-XCP API
PEAK-System Technik

The PCAN-XCP API is a programming interface for the communication between Windows® applications (Masters) and electronic control units (Slave ECUs)...
View full details

$0

Sale
Sale

$99

LabVIEW API for PLIN
KDI Digital Instrumentation

Leveraging the PLIN© API from PEAK-System, the LabVIEW® API for PLIN allows you to exchange CAN messages via CAN 1.0 / 2.0B and CAN FD with the PLI...
View full details

$99

Sale
Sale

$1,979

CANopen Magic Ultimate
Embedded Systems Academy

Professional CANopen configuration, simulation and analysis tool. High accuracy timestamps, Electronic Datasheet support, network configuration and...
View full details

$1,979

Sale
Sale

$589

CANopen Magic Standard
Embedded Systems Academy

Low cost basic CANopen configuration and analysis tool. Runs on all versions of Windows and provides access to Object Dictionary entries, shows mes...
View full details

$589

Sale
Sale

$189

CANcrypt
Embedded Systems Academy

Commonly used security methods for authentication and encryption/decryption on the Internet cannot be easily applied to CAN/CANopen. ESAcademy's so...
View full details

$189

Sale
Sale

$399

CANinterpreter (USB dongled floating license)
SYS TEC electronic GmbH

CAN Monitoring and Recording Software The CANinterpreter is a versatile tool for monitoring, recording, and analyzing data traffic on CAN-Networks....
View full details

$399

Sale
Sale

from $199

PCAN-Diag FD J1939 Add-in
PEAK-System Technik

SAE J1939 describes communication in utility vehicles via CAN. Using PGs (Parameter Groups) and SPs (Suspect Parameters), the standard defines mess...
View full details

from $199

Sale
Sale

from $6,699

CANopen Source Code
SYS TEC electronic GmbH

CANopen Master & Slave Source Code CiA 301 The CANopen source code implements the complete functionality pursuant to the CiA 301 draft standard...
View full details

from $6,699

Sale
Sale

$349

CANopen plug-in for CANinterpreter
SYS TEC electronic GmbH

CANopen Interpretation add-on* for CANinterpreter The CANopen Interpreter interprets all received CAN messages according to the CANopen protocol an...
View full details

$349

Sale
Sold out

from $1,699

CANopen DeviceExplorer Full Version
SYS TEC electronic GmbH

The CANopen DeviceExplorer is a versatile tool for development, testing, diagnostics and service tasks. It provides CANopen master functionalities ...
View full details

from $1,699

Sold out
Sale

from $309

CANopen and CANopen FD Firmware for PCAN-MicroMod FD (software only)
Embedded Systems Academy

Note: The last three digits of the Part Number signifies the number of licenses Part Number Number of Licenses ES-FWIA-MM-005 For up to 5 ins...
View full details

from $309

Sale
Sale

$2,995

CiA 304 SRDO Add-on for CANopen Source Code
SYS TEC electronic GmbH

CiA 304 SRDO Add-on to CANopen Master & Slave Source Code The CiA 304 SRDO Add-on provides all services and functionality compliant to CiA 304 ...
View full details

$2,995

Sale
Sale

$149

CANvision Protocol Monitor
GEMAC

CANvision® - Protocol monitor is an efficient software tool for the development, analysis and monitoring of CAN bus systems. Its client/server arch...
View full details

$149

Sale
Sale

$799

PCAN-FMS Simulator 2
PEAK-System Technik

Windows® Software for Simulating CAN Data According to FMS Standard The FMS (Fleet Management System) and Bus-FMS protocols provide a manufacturer-...
View full details

$799

Sale
Sale

$2,289

CANopen Magic Pro DLL (Windows)
Embedded Systems Academy

Professional grade Application Programmer Interface DLL. Provides a CANopen platform to build PC applications. Full documentation, example applicat...
View full details

$2,289

Sale
Sale

$669

CANopen Architect Professional
Embedded Systems Academy

The capabilities of CANopen® nodes are described by Electronic Datasheets (EDS) files. When CANopen® modules are sold or made available to third pa...
View full details

$669

Sale